Sharp C3400C, Service Manual

Page: 6 / 64

CD-C472/C3400/C3400C/C3800/C3800C
– 6 –
OPERATION MANUAL
S
E
TTI
NG
THE
CLO
CK
POWER CLOCK MEMORY/ SET TUNING/ TIME ( )
AM 12:00
AM 0:00
0:00
2 3
4
7
6 5
8
9
(Main unit operation)
1
Press the POWER switch to turn the power off.
2
Press the CLOCK button.
3
Within 3 seconds, press the MEMORY/SET button.
4
Press
the
TUNING/TIME
(
or
) button to select the time
display mode.
"AM 12:00"
→
Th
e 1
2
-h
ou
r di
sp
lay
w
ill
ap
pe
ar
.
(
A
M
1
2
:0
0
-
P
M
1
1
:5
9
)
"A
M
0:
00
"
→
T
h
e 1
2
-h
ou
r di
sp
la
y
w
ill
ap
pe
ar
.
(
A
M
0
:0
0
-
P
M
1
1
:5
9
)
"0
:0
0
"
→
Th
e 2
4
-h
ou
r dis
pl
ay
w
ill a
p
p
e
a
r.
(
0
:0
0
-
2
3
:5
9
)
●
Note that this can only be set when the unit is first installed or it has been reset (see page 18).
5
Press the MEMORY/SET button.
6
Press
the
TUNING/TIME
(
or
) button to adjust the hour.
●
Press the TUNING/TIME button once to advance the time by 1 hour. Hold it down to advance continuously.
●
When the 12-hour display is selected, "AM" will change auto- matically to "PM".
7
Press the MEMORY/SET button.
8
Pr
e
s
s
th
e
TU
N
IN
G
/TIM
E
(
o
r
) b
u
tto
n
to
a
d
ju
s
t
th
e
minutes.
●
Press
the
TUNING/TIME
(
or
) button once to advance
the time by 1 minute. Hold it down to change the time in 5 minute intervals.
●
The hour setting will not advance even if minutes advance from "59" to "00".
9
Press the MEMORY/SET button.
●
The clock starts operating from "0" seconds. (Seconds are not displayed.)
Note:
●
In the event of a power failure or when the AC power cord is disconnected, the clock display will go out. When the AC power supply is restored, the clock display will flash on and off to indicate the time when the power failure occurred or when the AC power cord was disconnected. If this happens, follow the procedure below to change the clock time.
To change the clock time:
When the POWER switch is set to OFF. ①
Press the MEMORY/SET button.
②
Perform steps 6 - 9 above.
When the POWER switch is set to ON. ①
Press the CLOCK button.
②
Within 3 seconds, press the MEMORY/SET button.
③
Perform steps 6 - 9 above.
To see the time display:
Press the CLOCK button.
●
The time display will appear for about 3 seconds.
To change the time display mode: ①
Perform steps 1 - 2 in the section "RESETTING THE MICRO- COMPUTER", on page 18.
②
Perform steps 1 - 9 above.
In this example, the clock is set for the 12-hour (AM 12:00) system.
RE
S
E
TTI
NG
THE
MI
CRO
CO
MP
UTE
R
Reset the microcomputer under the following conditions:
●
To erase all of the stored memory contents (clock and timer settings, and tuner and CD presets).
●
If the display is not correct.
●
If the operation is not correct.
1
Press the POWER switch to turn the power off.
2
W
h
ile
p
res
si
ng
d
o
w
n
t
h
e V
O
L
U
M
E
bu
tt
o
n
an
d t
h
e
/
button, hold down the POWER button for at least 1 sec
-
ond.
Caution:
●
The operation explained above will erase all data stored in memory including clock and timer settings, and tuner and CD presets.
1,2
2
2