manualshive.com logo in svg

Sharp Blue Treak LH75400, User Manual, Page: 191 / 502

Share
Download
Sharp Blue Treak LH75400 User Manual Download Page 191

Direct Memory Access Controller

LH75400/01/10/11 (Preliminary) User’s Guide

12-10

7/15/03

NOTE: If you use a SoSize/DeSize of ‘01’, set the 

SoBurst value to ‘01’.

4:3

SoSize

Source-to-DMA data width

See Table 12-6. For memory-to-peripheral operations, 

if bits [6:5] = ‘00’, bits [4:3] must = ‘00’. If bits [6:5] = ‘01’, bits [4:3] must = ‘01’.

2

DeInc

Current Destination Register Increment

Enables the Current Destination Register 

increment after each DMA-to-destination data transfer.

0 = Current Destination Register remains unchanged.
1 = Current Destination Register is incremented.

1

SoInc

Current Source Register Increment

Enables the Current Source Register incre-

ment after each source-to-DMA data transfer. 

0 = Current Source Register remains unchanged, holding the same value during the 

entire DMA transfer.

1 = Current Source Register increments as data transfers from a source to the DMA. 

The value increments by the HSIZE value at the end of the address phase of the 
AHB transfer.

0

Enable

DMA Controller Enable/Disable 

Enables or disables the DMA Controller. The 

Source Base, Destination Base, and Maximum Count Registers must be set before the 
DMA is enabled. The state machine clears this bit when a data transfer finishes. If the 
software resets this bit during a transfer, that stream interface is reset.

0 = DMA data transfer is disabled.
1 = DMA data transfer is enabled.

Table 12-6. DMA Data Width

SoSize/DeSize

AHB DATA WIDTH

00

1 byte

01

1 half-word (2 bytes)

10

1 word (4 bytes)

11

Reserved

Table 12-7. DMA Burst Size

SoBurst

AHB BURST TYPE

00

Single

01

4 incrementing

10

8 incrementing

11

16 incrementing

Table 12-5. CTRL Register Definitions (Cont’d)

BIT

NAME

FUNCTION

Summary of Contents for Blue Treak LH75400























































































































































































































































































































































































































































































































Reviews:

No comments