background image

23

KEY OPERATOR PROGRAMS

1.

Select a paper tray on the touch panel.

2.

Select a paper size for [EXTRA] setting.
To select a size of AB series, press the “AB” key and
select a paper size.

Select the paper size which matches the paper to be loaded into
the paper tray.

This setting can also be used for paper trays in an optional 500-
sheet paper drawer (AR-CS2).

3.

Press the “OK” key.

Require Key Operator Code

This program is used to prevent the copier from being started by
people other than key operator. If this program is set, the message

ENTER KEY OPERATOR CODE. -----

” will appear each time the

power switch is turned to the “ON” position.

To require key operator code entry for access to the copier,
press the check box of “REQUIRE KEY OPERATOR CODE”
to display a check mark in the check box.
To enable access to the copier without key operator code
entry, press the check box of this program again to clear the
check mark in the check box.

Stream Feeding Mode

This program is only available when the optional RADF is installed and
used to enable the stream feeding mode of the optional document
feeder. When the stream feeding mode is enabled, additional originals
which are set in the document feeder tray within 5 seconds after the last
original in a stack was fed will be fed and copied automatically.

To enable the stream feeding mode, press the check box of
“STREAM FEEDING MODE” to display a check mark in the
check box.
To disable this mode, press the check box of this program
again to clear the check mark in the check box.

KEY OPERATOR PROGRAMS

SIZE SETTING FOR [EXTRA]

INCH

PAPER TRAY

OK

11 17

8/ 14

2

1

2

1

2

1

2

1

4

1

2

1

2

1

2

1

8/ 13

8/ 11

1

2

3

4

8/ 11R

5/ 8/

7/ 10/R

EXTRA

AB

Summary of Contents for AR-C150





































Reviews:

Related manuals for AR-C150