11
12
Option menu (Continued)
Adjusting the PC image manually
Ordinarily you can easily adjust the picture as
necessary to change image position using Auto
sync. In some cases, however, manual adjustment is
needed to optimise the image.
Selected item
Description
H-Position
Centres the image by moving it to the left
or right.
V-Position
Centres the image by moving it up or
down.
Clock
Adjusts when the image fl ickers with
vertical stripes.
Phase
Adjusts when characters have low
contrast or when the image fl ickers.
NOTE
• For resetting all “Fine sync” items to the factory preset
values, press
a
/
b
to select “Reset”, press
ENTER
, press
a
/
b
to select “Yes”, and then press
ENTER
.
• Images may not be displayed properly depending on the
settings and/or input signals.
Input signal
• Some input signals may have to be registered
manually to display properly.
• The pairs of input signals (resolutions) in the list
below are not distinguishable when received.
In such case, you have to set the correct signal
manually. After setting once, it will display when the
same signal (resolution) is input again.
1280
g
768
1360
g
768
H
Demo
Displays information about some TV features.
(On, Off)
Press
RETURN
, select “Off”, and then press
ENTER
to stop the Demo mode autoplay function.
NOTE
• The Demo mode is available only in English version.
• When “Demo” is set to “On”, autoplay will start. Therefore,
only
RETURN
button will be functioning.
H
System data
This function allows you to update the TV to the
latest software using a USB device. You must
update the software through the USB terminal.
Setup menu (Continued)
H
Reset
If complex adjustments are made and the settings
cannot be restored to normal, you can reset the
settings to the factory preset values.
NOTE
• If you execute “Reset”, all the settings such as “Picture”,
“Audio” and “Programme setup” will be reset to the factory
preset values.
Option menu
Output volume select
Option
Input select
Fine sync.
Demo
System data
Auto volume
PC audio select
4
Audio only
4
Colour system
4
H
PC audio select
When using the INPUT 4 terminal or INPUT 1
terminal, you must select which terminal uses the
AUDIO IN (R/L) jack for analogue audio input.
Selected item
Description
HDMI
When connecting devices (including a
PC) with DVI/HDMI cable to the INPUT 1
terminal and inputting analogue audio
signals from the AUDIO IN (R/L) jack.
RGB
When connecting a PC to the INPUT 4
terminal, and inputting analogue audio
signals from the AUDIO IN (R/L) jack.
NOTE
• When connecting devices (including a PC) with digital
audio signal by using HDMI-certified cable to INPUT 1
terminal, you must set to “RGB”. If “HDMI” is set, there
will be no sound output.
H
Output volume select
Allows you to select what controls the audio output.
Selected item
Description
Fixed
• Sound via speakers is adjusted with
VOL
k
/
l
on the remote control or
the TV.
• Sound via the AUDIO OUT terminal is
not adjustable and constantly outputs.
Variable
• Sound via the AUDIO OUT terminal
is adjusted with
VOL
k
/
l
on the
remote control unit or the TV.
• Sound via speakers is muted.
NOTE
• When “Output volume select” is set to “Variable”, all Audio
menu item cannot be adjusted.
Picture and still image
You can freeze a motion picture on the Display.
1
Press
FREEZE
.
• A still image displays.
2
Press
FREEZE
again to exit still image.
NOTE
• The still image automatically goes out after 30 minutes.
ECO mode
This function enables you to reduce the backlight
brightness in order to decrease the power
consumption and increase the backlight life span as
shown in the following table.
Selected item
Description
ECO 1
Reduces the backlight brightness.
ECO 2
Reduces the backlight brightness more
than “ECO 1”.
ECO Off
Normal setting of backlight brightness.
ECO status will be displayed on the channel
information window.
PC compatibility chart
Resolution
Horizontal
Frequency
Vertical
Frequency
VESA
Standard
VGA
640
g
480
31.5 kHz
60 Hz
✓
SVGA
800
g
600
37.9 kHz
60 Hz
✓
XGA
1024
g
768
48.4 kHz
60 Hz
✓
WXGA
1360
g
768
47.7 kHz
60 Hz
✓
SXGA 1280
g
1024
64.0 kHz
60 Hz
✓
SXGA+ 1400
g
1050
65.3 kHz
60 Hz
✓
1080p 1920
g
1080
67.5 kHz
60 Hz
✓
Power Management is a registered trademark of Sun
Microsystems, Inc.
VGA, SVGA, XGA, WXGA, SXGA and SXGA+ are
registered trademarks of International Business Machines
Corporation.
H
Input select
For setting the signal type of external equipment.
Input source
Selectable item
INPUT3
Component, Video
H
Auto volume
Different sound sources, fairly often do not have the
same volume level, for example the changing from
movie to the advertisements. Auto volume solves this
problem and equalises the volume levels. (On, Off)
H
Audio only
When listening to music from a music programme,
you can set the display off and enjoy audio only.
Selected item
Description
On
Audio is output without screen image.
Off
Both screen images and audio are
output.
NOTE
• When you make operations that change the picture on the
TV such as by changing the input source, the “Audio only”
function is set to “Off”.
H
Colour system
You can change the colour system to one that is
compatible with the image on the screen. (Auto,
PAL, SECAM, NTSC 3.58, NTSC 4.43, PAL-60)
NOTE
• If “Auto” is selected, colour system for each channel is
automatically set. If an image does not display clearly,
select another colour system (e.g. PAL, NTSC 4.43).
• “Colour system” is selectable only when inputting a
composite signal.
H
Fine sync. (PC input mode only)
Adjusting the PC image automatically
Auto sync.
This function enables the screen to be automatically
adjusted to its best possible condition when the
analogue terminals of the TV and PC are connected
with a commercially available RGB cable, etc.
NOTE
• Auto sync. is likely to succeed when an input PC image
has wide vertical stripes (e.g. pattern with high contrast
stripes, or cross-hatched).
It may fail when an input PC image is solid (low contrast).
01_LC-24DC50M_EN.indd 6
01_LC-24DC50M_EN.indd 6
21-Oct-11 10:19:52 AM
21-Oct-11 10:19:52 AM
