Sharp AL-1000 Series Service Manual Download | Manualshive

Page: 70 / 93

background image

4. Trouble Codes

Main code

Sub code

Trouble content

Detail of trouble

E7

03

HSYNC cannot be
detected.

LSU (laser diode, reception element, APC circuit) trouble
LSU drive circuit (ASIC) trouble

E7

04

CCD white level trouble

CCD drive circuit (CCD PWB, ASIC harness) trouble
Copy lamp lighting trouble (Copy lamp, invertor PWB)

E7

05

CD black level trouble

CCD drive circuit (CCD PWB, ASIC, harness) trouble

E7

12

Shading trouble
(white correction)

Dirt on white plate for scanning white level

E7

14

ASIC connection trouble

Improper connection between CPU and ASIC (pattern cut, improper connection
of lead pin)

E7

15

Copy lamp OFF trouble

Copy lamp or copy lamp drive circuit (invertor PWB) trouble Copy lamp
disconnection

L1

00

Feed is not completed
within the specified time.

When the mirror base is returned for the specified time (6 sec) in mirror initializing
after turning on the power, the mirror home position sensor (MHPS) does not
turn OFF. Or when the mirror base is fed for the specified time (about 6 sec)
after start of copy return, the mirror home position sensor (MHPS) does not turn
OFF.

L3

00

Return is not completed
within the specified time.

When the mirror base is returned for the specified time (6 sec) in mirror
initializing after turning on the power, the mirror home position sensor (MHPS)
does not turn ON.Or when the mirror base is returned for the specified time
(about 6 sec) after start of copy return, the mirror home position sensor (MHPS)
does not turn ON.

L4

01

Main motor lock

When the main motor encoder pulse is not detected for 100msec.

L6

10

Polygon motor lock

The lock signal (specified rpm signal) does not return within a certain time (about
20sec) from starting the polygon motor rotation

H2

00

Thermistor open detection

The fusing thermistor is open.

H3

00

Heat roller abnormally high
temperature

The fusing temperature rises above 240°C.

H4

00

Heat roller abnormally low
temperature

The fusing temperature does not reach 185°C within 27 sec of turning on the
power, or the fusing temperature keeps at 140°C.

U2

01

Counter sum check error

When the counter check sum value stored in the EEPROM is abnormal.

U2

04

EEPROM serial
communication error

When a communication trouble occurs with the EEPROM.

CH

(Blinking)

-

TD cartridge not installed

Check if TD cartridge is installed.

AL-1000/1010

10-11

«
...
68
69
70
71
72
...
»

Summary of Contents for AL-1000 Series






























































































Reviews:

No comments

Related manuals for AL-1000 Series

Brand: Oce Pages: 220

Brand: Epson Pages: 53

Brand: Ricoh Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands