background image

USING YOUR AIR CONDITIONER

 indicatorfan

6

5

3 4

2

1

7

8

Light indicates the unit

is in the temperature or

delay time Set mode.

Power

Mode

  Fan 

Speed

Timer

Filter check

Set

Temp

Cool
Energy Saver
Fan Only
Dry

Auto
High
Med
Low

Time

Electronic Control Panel & Remote Control

CONTROL PANEL

NOTE: This display always shows the room temperature in Fan Mode except when setting the Set temperature or 

the Timer

Air Conditioner Controls

1. 

Power Button:

 Turns the air conditioner on

 

and off

2. 

Digital Display:

 Under ON status without timer 

setting, the operation mode is Auto, Cool, 

Energy Saver or Dry mode, and the set 

temperature will be displayed. Under ON status 

without timer setting, the operation mode is fan 

mode and the ambient temperature will be 

displayed. Time will be displayed under timer 

setting or timer preview.

3. 

Temperature Set:

 Use these buttons on the 

control panel and remote to increase or 

decrease the Set Temperature (the desired 

room temperature) in cooling, energy saver and 

dry mode. The SET light will light up when 

setting the temperature 

4. 

Timer Set:

 Use these buttons on the control 

panel and remote to set the Timer. Each press 

of the Timer (DELAY) buttons will increase or 

decrease the timer. For timer instructions 

see #7.

5. 

Fan Speed & Auto Fan:

 Use the fan speed 

buttons to change the fan speed. Choose 

between Low, Medium, High, and Auto.

6. 

Mode Button:

 Press the mode button to cycle 

through the various modes: Cooling, Energy 

Saver, Fan only, Dry (Dehumidifier) and Auto.

7. 

Auto-on Timer:

 When the air conditioner is 

off, it can be set to automatically turn on in 

0.5-24 hours at the previous set mode and fan 

setting. To set the Auto-on Timer, press the 

TIMER button on the unit or remote control. 

The timer can be set in 0.5 hour 

increments 

below 10 hours and in 1 hour increments for 

10 hours or above. The Set light will turn on 

while setting.

 

Auto-off Timer:

 When the air conditioner is 

on, it can be set to automatically turn off in 

0.5-24 hours. To set the Auto-off Timer, press 

the TIMER button on the unit or remote 

control. The timer can be set in 0.5 hour 

increments below 10 hours and in 1 hour 

increments for 10 hours or above. The SET 

light will turn on while setting.

•  To see the remaining time, press the TIMER 

Button. To change the timer setting use the 

▲/▼ on the unit or the +/- buttons on the 

remote. 

•  During preview of timer or timer setting, 

press Timer button on the panel or remote

8.  Filter Check: After the fan rotates for 250 total 

hours, the filter check light will turn on to 

remind the user to clean the filter. Press the 

Filter check button once the filter is cleaned to 

reset the reminder function.

Summary of Contents for AF-Q100VX





















Reviews: