manualshive.com logo in svg

Sharp 679, User Manual

The Sharp 679 User Manual is a comprehensive guide that allows you to effortlessly navigate every feature of your device. Download this manual for free from our website and unleash the full potential of your Sharp 679 with ease and confidence.

Share
Download
background image

Regulatory notices for wireless products

This section contains regulatory information that applies only to wireless models.

If in doubt as to whether your model is a wireless model, go to our website.

Modular component notice

Wireless models contain one of the following modular components:

Regulatory Type/Model Number LEX-M07-001; FCC ID:IYLLEXM07001; IC:2376A-LEXM07001
Regulatory Type/Model Number LEX-M08-001; FCC ID:IYLLEXM08001; IC:2376A-LEXM08001

To determine which modular components are installed in your particular product, refer to the labeling on your
actual product.

Exposure to radio frequency radiation

The radiated output power of this device is far below the radio frequency exposure limits of the FCC and other
regulatory agencies. A minimum separation of 20 cm (8 inches) must be maintained between the antenna and
any persons for this device to satisfy the RF exposure requirements of the FCC and other regulatory agencies.

Industry Canada (Canada)

This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.

Industrie Canada (Canada)

Cet appareil est conforme aux normes RSS exemptes de licence d'Industrie Canada. Son fonctionnement est
soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interférences et (2) il doit accepter
toutes les interférences, y compris les celles qui peuvent entraîner un fonctionnement indésirable.

European Community (EC) directives conformity

This product is in conformity with the protection requirements of EC Council directive 2014/53/EU on the
approximation and harmonization of the laws of the Member States relating to radio equipment.

A declaration of conformity to the requirements of the Directives may be obtained at

www.lexmark.com/en_us/about/regulatory-compliance/european-union-declaration-of-conformity.html

.

Compliance is indicated by the CE marking:

Notices

211

Summary of Contents for 679




























































































































































































































Reviews:

No comments

Related manuals for 679

Canon Pixma G1000 series Getting Started preview
Pixma G1000 series
Brand: Canon Pages: 2
Canon Pixma G1000 series Service Manual preview
Pixma G1000 series
Brand: Canon Pages: 80
Canon IMAGERUNNER ADVANCE C5051 Frequently Asked Questions Manual preview
IMAGERUNNER ADVANCE C5051
Brand: Canon Pages: 44
EBS 2500 Installation And First Startup preview
2500
Brand: EBS Pages: 4
NCR 7156 Setup And User Manual preview
7156
Brand: NCR Pages: 38
TallyGenicom 2440 Quick Start Manual preview
2440
Brand: TallyGenicom Pages: 38
Oki MC160N User Manual preview
MC160N
Brand: Oki Pages: 268
Oki LE810DT Manual De L'Utilisateur preview
LE810DT
Brand: Oki Pages: 54
Oki LE810DT Guías Del Usuario Manual preview
LE810DT
Brand: Oki Pages: 54
Oki MB460MFP Manual Do Usuário preview
MB460MFP
Brand: Oki Pages: 202
Oki MB460MFP Manual De L'Utilisateur preview
MB460MFP
Brand: Oki Pages: 201
Oki ES2232a4 User Manual preview
ES2232a4
Brand: Oki Pages: 103
Oki ES3037 User Manual preview
ES3037
Brand: Oki Pages: 256
Oki B710dn Hardware Manual preview
B710dn
Brand: Oki Pages: 2
Oki B710dn Material Safety Data Sheet preview
B710dn
Brand: Oki Pages: 36
Oki B6500 Series Guia Del Usuario De Redes preview
B6500 Series
Brand: Oki Pages: 63
Oki B6500 Series Customer Support Information preview
B6500 Series
Brand: Oki Pages: 28
Oki B6500 Series Service Manual preview
B6500 Series
Brand: Oki Pages: 616

Brands by name

Popular brands

Load more brands