background image

E9

TROUBLESHOOTING

The following problems do not always indicate a hardware failure. Therefore, please use the
troubleshooting guide below before calling for repair service.
If, after following the guide none of the remedies work, unplug the TV set and call for service.

Quick Service Check List  

Increase the volume.

Try fine tuning to correct.

Remote control does not work.

Bars on screen.

Picture distorted.

Picture rolls vertically.

No colour.

Poor reception on some channels.

Picture weak.

Picture lines or streaks.

Picture ghosting.

Picture blurred.

Sound OK, picture poor.

Picture OK, sound poor.

No picture or sound.

Contrast setting in picture mode might be all the way to the minus side.  
Press the 

NORMAL 

button on the remote control to correct. 

 

Check batteries in the remote control.

Adjust COLOUR control.

Turn OFF using the 

POWER

 switch, then turn ON again after 8 minutes. 

Check for local interference.

If outside antenna is used, check for broken wires. 

Antenna not connected to terminal at the back of the TV set. 

POWER 

switch of TV not ON.

TV not plugged in. Outlet power OFF.

Try a new channel to check for possible station trouble. 

Possible Causes/Remedies

Problems

This unit is equipped with a microprocessor. Its performance could be adversely affected by external electrical
noise or interference. If this should happen, unplug the unit and plug it in again after a few minutes.

MODEL

21S-FX10M

Receiving System

PAL – B/G, I, D/K

SECAM – B/G, D/K, K1

NTSC 4.43 – B/G, I, D/K

Receiving Frequency

44.25 MHz – 863.25 MHz

Channel Tuning

100-Channel Electronic Tuner with Full Auto Tuning System

Terminals

Audio/video input 

×

 2 (front 

×

 1, rear 

×

 1), Audio/video output 

×

 1 (rear),

M.P. IN jack 

×

 1 (front), DVD input (COMPONENT) 

×

 1 (rear)

Sound Output

3 W (RMS) 

×

 4, total 12 W (RMS)

Power Source

AC 110 – 240V, 50/60 Hz

Power Consumption

98 W

Dimensions

577 (W) 

×

 467 (H) 

× 

340 (D) mm

Weight

20 kg (Approx.)

• Design and specifications are subject to change without notice.
• Receiving system: These receiving systems, encompassing all currently available technology, include those with

planned broadcast, videotape and laserdisc hardware and software.

SHARP CORPORATION

E10

SPECIFICATIONS

21S-FX10M[EN].p65

11/21/07, 5:24 PM

4

Summary of Contents for 21S-FX10M

Page 1: ...with care Quick stops excessive uneven surfaces may cause the equipment and cart combination to overturn ntion fire never place any type of candle or naked flames on the top or near the TV set nstallation ins switch with a separation of at least 3 mm in each pole shall be ed in the electrical installation of the building SAFETY PRECAUTIONS E2 ACCESSORIES Connecting to an antenna Connecting to an a...

Page 2: ...r intensity BRIGHTNESS For less brightness For more brightness TINT To move tint toward red To move tint toward green SHARPNESS For less sharpness For more sharpness PICTURE NR WHITE TEMP To more reddish background To more bluish background see note below ON OFF TINT can only be selected and adjusted when receiving NTSC broadcasts Picture Noise Reduction Noise might be generated on images when pla...

Page 3: ...el number appear on the screen Press once again The display disappears TV VIDEO Number buttons CH CH B C D A 5 OFF 2 3 0 Mute Silences the sound Press Press appears on the screen and the sound is silenced Press the volume returns to its previous level Mute will be cancelled if the or is pressed at any time Channel recall Switches back to the channel you were watching just before the current channe...

Page 4: ...en wires onnected to terminal at the back of the TV set h of TV not ON d in Outlet power OFF nnel to check for possible station trouble Possible Causes Remedies Problems uipped with a microprocessor Its performance could be adversely affected by external electrical erence If this should happen unplug the unit and plug it in again after a few minutes 21S FX10M stem PAL B G I D K SECAM B G D K K1 NT...

Reviews: