background image

SHARP CORPORATION

This unit is equipped with a microprocessor. Its performance could be adversely affected by external electrical 
noise or interference. If this should happen, unplug the unit and plug it in again after a few minutes.

The following problems do not always indicate a hardware failure. Therefore, please use the 
troubleshooting guide below before calling for repair service.
If, after following the guide none of the remedies work, unplug the TV set and call for service.

 E9 

TROUBLESHOOTING

Quick Service Check List  

Increase the volume.

Try fine tuning to correct.

Remote control does not work.

Bars on screen.

Picture distorted.

Picture rolls vertically.

No colour.

Poor reception on some channels.

Picture weak.

Picture lines or streaks.

Picture ghosting.

Picture blurred.

Sound OK, picture poor.

Picture OK, sound poor.

No picture or sound.

Contrast setting in picture mode might be all the way to the minus side.  
Press the 

NORMAL 

button on the remote control to correct. 

 

Check batteries in the remote control.

Adjust COLOUR control.

Turn OFF using the     

POWER

 switch, then turn ON again after a minute. 

Check for local interference.

If outside antenna is used, check for broken wires. 

Antenna not connected to terminal at the back of the TV set. 

    

POWER 

switch of TV not ON.

TV not plugged in. Outlet power OFF.

Try a new channel to check for possible station trouble. 

Possible Causes/Remedies

Problems

•  Design and specifi cations are subject to change without notice.
•  Receiving system: These receiving systems, encompassing all currently available technology, include those with planned 

broadcast, videotape and laserdisc hardware and software.

MODEL

14T1-U

Receiving System

World multi 18 system
PAL – B/G, I, D/K 

SECAM – B/G, D/K, K1 

NTSC 4.43 – B/G, I, D/K

Receiving Frequency

48.25 MHz – 863.25 MHz

Channel Tuning

100-Channel Electronic Tuner with Full Auto Tuning System

Terminals

Audio/video input × 2 (front x 1, rear x 1), Audio/video output × 1 (rear),
Headphone jack x 1 (front)

Sound Output

3 W (RMS) × 1

Power Source

AC 110 – 240V, 50 Hz / 60 Hz

Power Consumption

62 W

Dimensions

352 (W) × 334 (H) × 355 (D) mm

Weight

8.8 kg (Approx.)

 E10 

SPECIFICATIONS

14T1-U_EN.indd   4

14T1-U_EN.indd   4

10/25/07   11:42:27 AM

10/25/07   11:42:27 AM

Summary of Contents for 14T1-U

Page 1: ...e wall outlet immediately if the TV set begins to make any unusual noises or gives off smoke or an unusual smell Then call your dealer for service Servicing To reduce the risk of electric shock do not remove the back of the cabinet This TV set contains dangerous voltage Unstable surface and shocks Do not place this TV set on an unstable cart stand shelf or table The TV set may fall causing serious...

Page 2: ...he antenna cable to the TV set 3 Plug in the AC POWER cord to the wall outlet Press both CH and CH on TV set for more than two seconds during normal screen the LANGUAGE menu will appear Press CH CH to select desired language and to set the language Once language setup is completed CH SETTING menu will displayed AUTO Press and Auto Channel Tuning is started Auto tuning bar will shown during Auto Se...

Page 3: ...Noise Reduction Noise might be generated on images when playing deteriorated video tapes or when receiving broadcasts with relatively weak signals In these cases set PICTURE NR to ON to reduce the noise However when receiving good images without noise you can get better image quality by turning OFF this feature WHITE TEMP can only be adjusted on PICTURE menu E7 SELECTING MENU ITEMS PICTURE menu CO...

Page 4: ... the remote control Adjust COLOUR control Turn OFF using the POWER switch then turn ON again after a minute Check for local interference If outside antenna is used check for broken wires Antenna not connected to terminal at the back of the TV set POWER switch of TV not ON TV not plugged in Outlet power OFF Try a new channel to check for possible station trouble Possible Causes Remedies Problems De...

Reviews: