Shark GARDEN 550 Instruction & Assembly Manual Download Page 3

 

- 3 - 

 

GENERAL WARNINGS 

 

READ and UNDERSTAND this manual completely before using Utility Dump Cart. 

Operator  must  read  and  understand  all  safety  and  warning  information,  operating  instructions, 
maintenance  and  storage  instructions  before  operating  this  equipment.  Failure  to  properly  operate  and 
maintain the utility dump cart could result in serious injury to the operator or bystanders. 
 

Operation Warnings 

  Do not at any time carry passengers sit or stand on the cart.   

  Do not allow children to play on, stand upon or climb in the cart. 

  Always inspect the cart before using to assure it is in good working condition. 

  Replace or repair damaged or worn parts immediately. 

  Always check and tighten hardware and assembled parts before operation. 

  Do not exceed equipment maximum load capacity of 550 kg. 

  Avoid large holes and ditches when transporting loads. 

  Be careful when operating on steep grades (hill) the cart may tip over. 

  Always operate at reduce speed in rough terrain, along creeks, ditches and on hillsides. 

  Do not operate close to creeks, ditches and public highways. 

  To avoid personal injury and/or equipment damage DO NOT EXCEED 25 km/h. 

  Always use caution when loading and unloading the cart. 

  Only tow with recommended vehicles (Lawn/Garden Tractors and ATVs). 

  Always secure and lock dump cart to the vehicle hitch before operating.   

 

Crush and Cut Hazards 

  Always keep hands and feet clear from moving parts while operating the equipment. 

  Always clear and keep work area clean when operating.   

  Always

 

wear safety gear, eye protection, gloves and work boots when operating the dump cart.

 

 

 

WARNING 

The  warnings,  cautions,  and  instructions  outlined  in  this  instruction  manual  cannot  cover  all 
possible  conditions  or  situations  that  may  occur.    It  must  be  understood  by  the  operator  that 
common sense and caution are factors which cannot be built into this product and must be supplied 
by the operator.

 

 

 

Assembly Is Required

 

This product requires assembly before use. See 

“Assembly” section for instructions.    Because of the 

weight and/or size of the utility dump cart, it is recommended that another adult be present to assist with 
the assembly.   

INSPECT ALL COMPONENTS

 closely upon receipt to make sure no components are 

missing or damaged. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for GARDEN 550
















Reviews: