Page 6
Shark DH3030HGB
Oil Burner
Burner Air Adjustment: The oil burner on this machine
is preset for operation at altitudes below 3000 feet. If
operated at higher altitudes, it may be necessary to adjust
the air shutter and air band setting. Adjust the air shutter
for a #1 or #2 smoke spot on the Bacharach scale.
To adjust, start machine and turn burner ON (refer to
Operation for details). Loosen two locking screws found
in the air shutter openings (refer to Figure 6) and close
air shutter until black smoke appears from burner exhaust
vent. Note air shutter position. Next, slowly open the air
shutter until white smoke just starts to appear. Turn air
shutter halfway back to the black smoke position
previously noted. Tighten locking screws.
If the desired position cannot be obtained using only the
air shutter, lock the air shutter in as close a position as
can be obtained, then repeat the above procedure on the
air band setting.
CAUTION: If white smoke appears from burner
exhaust vent during start-up or operation, discontinue
use and readjust air bands.
NOTE: If a flue is installed, have a professional ser-
viceman adjust your burner for a #1 or #2 smoke spot
on the Bacharach scale.
OPERATION
Before Starting
1. Read all manuals provided with this pressure washer.
Become familiar with location and function of all
operating and safety controls.
WARNING: Check hoses, fittings, wand, trigger gun
and fuel connections daily for signs of wear, cracks
and looseness, and replace as required.
2. Connect water supply hose to the garden hose con-
nector located on pump. The water faucet and supply
hose must be capable of providing a minimum of 3.0
gallons per minute (GPM).
3. Fill oil burner fuel tank. Use kerosene, #1 grade home
heating oil, #1 or #2 diesel fuel. DO NOT USE GASO-
LINE, CRANKCASE OIL DRAININGS, OR WASTE
OIL.
WARNING: Do not fill engine fuel tank while engine
is running or hot. Let engine cool before refueling or
spontaneous fire may result. Fuel spillage or vapors
could ignite if engine is hot.
4. Fill the engine fuel tank. Do not overfill, fill to the bot-
tom of filler neck only. Use lead free gasoline mini-
mum 86 octane, or lead free gasoline containing no
more than 15% MTBE. DO NOT use gasoline con-
taining more than 5% methanol or more than 10%
ethanol. Refer to the provided gasoline engine
manual for additional details.
5. Check pump and engine oil levels.
6. If detergents are to be used, only use detergents
intended for pressure washers. Follow instructions on
the detergent container.
IMPORTANT: Before installing pressure nozzle on
initial start-up, turn on the water supply and allow
water to run from the end of the wand until clear to
prevent the nozzle from clogging.
IMPORTANT: If the pressure washer has not been
used for an extended period of time, remove the pres-
sure nozzle from the end of the wand and turn on
water supply. Allow water to run from the end of the
wand until clear.
7. Install the proper pressure nozzle for your cleaning
needs on end of wand, refer to Figure 7.
IMPORTANT: The trigger gun provided with this pres-
sure washer is equipped with a manual trigger lock
to prevent accidental operation of the trigger gun,
refer to Figure 7. The trigger lock should be used
whenever the trigger gun is not in use.
Figure 7 - Nozzle Installation/Trigger Lock
Figure 6 - Burner Adjustment
TRIGGER LOCK
TRIGGER GUN
DUAL LANCE WAND
PRESSURE NOZZLE
AIR SHUTTER LOCKING SCREW
AIR SHUTTER
AIR BAND
AIR BAND
LOCKING SCREW
AIR SHUTTER LOCKING SCREW