Shark DG-2123 Operating Instructions And Parts Manual Download Page 9

sHarK dg  •  97-720  •  reV. 9/06

9

  

PRESSURE 

W

ASHER  

 OPERA

TOR’S MANU

AL

  

WARNING:  Some  detergents 
may  be  harmful  if  inhaled  or 
ingested, causing severe nau-
sea, fainting or poisoning. The 
harmful  elements  may  cause 
property  damage  or  severe 
injury.

STep 1: 

connect detegent injector to discharge nipple 

on machine. connect high pressure hose to injector 
with quick coupler. (check to make sure locking coupler 
sleeves are in proper position before applying water 
pressure).

STep  2:

  use  detergent  designed 

specifically  for  pressure  washers. 
Household  detergents  could  dam-
age  the  pump.  prepare  detergent 
solution  as  required  by  manufac-
turer.  Fill  a  container  with  pressure 
washer detergent. place filter end of 
detergent suction tube into detergent 
container.

STep 3:

 With safety latch on spray 

gun engaged, secure black detergent 
nozzle  into  quick  coupler.   

NoTe:

  

detergent  cannot  be  applied  using 
red, yellow, green or white nozzles.

STep  4:

 With  the  engine  running, 

pull  trigger  to  operate  machine.  liquid  detergent  is 
drawn into the machine and mixed with water. apply 
detergent to work area. do not allow detergent to dry 
on surface. 

IMPORTANT: You must flush the detergent injec-
tion system after each use by placing the suction 
tubeinto a bucket of clean water, then run the pres-
sure washer in low pressure for 1-2 minutes.

TheRMal pUMp pRoTeCTioN

if you run the engine on your pressure washer for 3-5 
minutes without pressing the trigger on the spray gun, 
circulating water in the pump can reach high tempera-
tures. When the water reaches this temperature, the 
pump protector engages and cools the pump by dis-
charging the warm water onto the ground. this thermal 
device prevents internal damage to the pump.

CleaNiNG TipS

pre-rinse cleaning surface with fresh water. place de-
tergent suction tube directly into cleaning solution and 
apply to surface at low pressure (for best results, limit 
your work area to sections approximately 6 feet square 
and always apply detergent from bottom to top). allow 
detergent to remain on surface 1-3 minutes. do not al-
low detergent to dry on surface. if surface appears to 
be drying, simply wet down surface with fresh water. 
if needed, use brush to remove stubborn dirt. rinse 
at high pressure from top to bottom in an even sweep-
ing  motion  keeping  the  spray  nozzle  approximately  
1 foot from cleaning surface. use overlapping strokes 
as you clean and rinse any surface. For best surface 
cleaning action spray at a slight angle.

Recommendations:

  •  Before  cleaning  any  surface,  an  inconspicuous 

area should be cleaned to test spray pattern and 

distance for maximum cleaning results.

  •   if painted surfaces are peeling or chipping, use 

extreme caution as pressure washer may remove 

the loose paint from the surface.

  •   Keep the spray nozzle a safe distance from the  

surface you plan to clean. High pressure wash a 

small area, then check the surface for damage. if 

no damage is found, continue to pressure wash-
ing.

       CAUTION - Never use:

  •   Bleach,  chlorine  products  and  other  corrosive 

chemicals

  •   liquids  containing  solvents  (i.e.,  paint  thinner, 

gasoline, oils)

  •   tri-sodium phosphate products
  •   ammonia products
  •   acid-based products
these chemicals will harm the machine and will dam-
age the surface being cleaned.

RiNSiNG

it will take a few seconds for the detergent to clear.  
apply safety latch to spray gun. remove  black soap 
nozzle from the quick coupler. select and install the 
desired high pressure nozzle. 

NoTe: 

You can also stop 

detergent from flowing by simply removing detergent 
siphon tube from bottle.

WaRNiNG

deTeRGeNT aNd GeNeRal CleaNiNG TeChNiQUeS

Soap Nozzle

detergent 

injector

discharge 

Nipple

Strainer

Quick 

Coupler

high 

pressure 

hose

Summary of Contents for DG-2123



































Reviews: