manualshive.com logo in svg

Shark BR-343087E, Operating Instructions And Parts Manual, Page: 8 / 28

Share
Download
Shark BR-343087E Operating Instructions And Parts Manual Download Page 8

96-718, 97-721, 97-723  •  REV. 8/05a

OPERA

T

OR’S MANU

AL

          

PRESSURE W

ASHER 

 

8

ASSEMBLY INSTRUCTIONS

STEP 1: Attach the high pres sure 
hose to the spray gun using tefl on 
tape on hose threads.

STEP 3: Release the coupler col lar 
and push the nozzle until the collar 
clicks.  Pull the nozzle to make sure 
it is seat ed properly.

STEP 5: Connect the high pres sure 
hose to the pump discharge nipple. 
Push coupler collar forward until 
se cure.

STEP 2: Pull the spring-load ed col-
 lar of the wand coupler back to in sert 
your choice of pres sure noz zle.

STEP 6: Connect garden hose to 
the cold water source.

STEP 7: Check inlet fi lters, remove 
debris, then connect garden hose 
to pump wa ter in let.  CAU TION: Do 
not run the pump with out wa ter or 
pump dam age will result.

Safety 

Latch

Spray 

Gun

High Pressure 

Hose

Wand 

Coupler

Pressure

Nozzle

Pressure 

Nozzle

Wand 

Coupler

Wand

Collar

Discharge 

Nipple

High Pressure Hose

Cold 

Water 

Source

Garden 

Hose

Pump 

Water Inlet

Garden 

Hose

Coupler Collar

Dipstick

STEP 4: Remove shipping cap and 
install oil dipstick. Check pump oil 
level by using dipstick or observe 
oil level in oil window (if equipped).  
Use 30 wt. non detergent oil.

Summary of Contents for BR-343087E





























Reviews:

No comments