background image

How to remove ShadeTree canopies for end 
of season storage.  

A

Use supplied allen wrench (J) to remove the top locks

at  the retracted

position

 as shown in the picture 

below.

B

Use supplied allen wrench (J) to loosen the roller lock

pin as shown in the picture below.

C

Roll the crossmembers out of the track, over the header

beams, and carefully through the decorative end caps.  

The tracks can remain up year-round.

D

If a canopy is dirty and requires washing before 

storage, simply spread the canopy on any flat surface. 

Use  a medium  to firm brush  or  broom  to remove  dirt 

particles while the fabric is still dry.  If this does not 

fully clean the canopy,  use a bucket of warm water and 

a mild soap, such as Ivory Snow to clean the fabric.  

E

Be sure to rinse well by hosing with a clear water.  Allow 

to air-dry completely in the sun before rolling canopies

up for storage. 

Do not store wet canopies! 

NOTE:  It’s best to store the canopies in a dry, well 

ventilated area.  

Care and cleaning of your ShadeTree 
system.

A

ShadeTree®  tracks

 should be cleaned regularly to

keep debris and dirt from accumulating and interfer-

ing with the

rollers

.  Simply use a mild detergent with a 

small soft brush, such as a toothbrush, and gently wipe

or brush along the inside of the tracks.  To maintain a

smoothly operating system, use the

ShadeTree®

EasyRider Track Lubricant

 in the roller tracks.  

Note:

Do NOT use oil or any wet lubricant, such as WD-40, 

on the tracks as it would attract more dirt. 

B

Fabric

 should be cleaned regularly before substances

such as dirt, roof particles, etc., are allowed to accumu-

late on and become embedded in the fabric.  The fabric

can be cleaned without being removed from the

cross

members

.  Simply brush off any loose dirt, roof particles, 

etc.  Hose down and clean with a mild natural soap in

lukewarm water (no more than 100º F.)  Rinse 

thoroughly to remove soap. 

DO  NOT  USE DETER-

GENTS! 

 For ultimate performance, use

ShadeTree®

Canopy Cleaner Mold & Mildew Stain Remover

.

C

For stubborn stains soak the fabric for approximately

20 minutes in a solution of no more than 1/4  cup (2

oz.) natural soap per gallon of water at approximately

100º F.  Rinse thoroughly in cold water to remove all of 

the soap. 

NOTE:

 Excessive soaking in bleach can 

deteriorate sewing threads.  This method of cleaning

may remove part of the water repellency and the fabric

should receive an application of an air-curing water-

repellent treatment, such as

ShadeTree® Canopy 

Cleaner Mold  & Mildew  Stain Remover

  and 

ShadeTree® Water  Repellent

or similar products, if 

water repellency is a factor.   

D

When washing or cleaning, 

DO  NOT  SUBJECT TO 

EXCESSIVE HEAT

  as  the fabric will shrink. 

DO  NOT 

STEAM PRESS OR DRY IN ELECTRIC OR GAS DRYERS

but allow to air dry.

E

In cases where canopies are taken down & stored, they 

should be cleaned and allowed to air dry, before being

stored in a dry, well ventilated area.  

ShadeTree Cool Living, LLC

 

for questions or assistance, call

 

800-894-3801

10

ShadeTree Canopy Systems

Assembly Instructions

Basic Pergola - Freestanding

Summary of Contents for Vinyl Basic Pergola













Reviews: