background image

6

Preparing for installation

Unpacking

Unpack the device and inspect it to ensure that it has not been damaged during transport.
The G-7 BeaSt is shipped with:

• 

2m (78 in.) power cable with IP connector

• 

Two omega brackets with 1/4-turn fasteners

• 

Safety information leaflet

Location / application

The fixture is IP66-rated and designed for both indoor and outdoor events. This means that it is protected from:

• 

Dust, to the degree that dust cannot enter the device in sufficient quantities as to interfere with its operation.

• 

Pressure jets of water from any direction.

When selecting a location for the device, ensure that:

• 

It is situated away from public thoroughfares and protected from contact with people.

•  It is not immersed in water.
• 

It has adequate ventilation.

When using the fixture with a DMX controller ensure that:

• 

According to RS485 standard, the DMX out of the last fixture should be terminated with a 120 Ohm resistor between pin 2 and 3.

• 

If the resistor is not installed, make sure that the DMX out is properly sealed by mounting the protection cap, in accordance 

with the ingress protection (IP) requirements.

• 

A maximum of 32 fixtures are allowed to be connected to the same DMX link.

Transportation

• 

Always use the supplied packaging or suitable flight case for transportation and storage.

• 

Release the tilt lock when transporting the fixture. Leaving the tilt lock blocked may cause damage to the fixture.

• 

Never carry the fixture by connected cables or wires, use the handles.

Installing/ Rigging the G-7 BeaSt

All  SGM  luminaries  have  locking  points  at  the  base  for  installation  and  rigging.  The 

distance between the points from centre to centre is always 106 mm (Fig. 2). The base 

of  the  standard  G-7  BeaSt  include  1/4  turn  fastener  cam  locks  to  mount  the  omega 

brackets. For further details of the bracket dimensions see page: 25, or contact SGM 

support.
The G-7 BeaSt may be installed in any orientation, with or without base, on the ceiling 

or on a wall surface. 

Always use the supplied omega brackets and lock with 1/4-turn fasteners (fig 3).

N.B.: The 1/4-turn fasteners are only locked when turned fully clockwise.

Depending on the structure, please use appropriate and secure methods for mounting the Omega bracket.

Figure 3: G-7 BeaSt base with Omega brackets

106 mm

 [ 4,2in ]

Ø 18 mm

  [ 0,7in ] 

Figure 2: SGM locking points 

A: Omega Bracket

B: 1/4-turn locking points (vertical view)

C: Omega Brackets attached to the 1/4-turn locking points (horizontal view)

A

B

C

Summary of Contents for G-7 BEAST




























Reviews: