SEW MOVIFIT SC series Operating Instructions Manual Download

Page: 129 / 148

Technical Data

Hygenicplus version

Operating Instructions – MOVIFIT

129

10.9 Hygenic

plus

version

10.9.1 Properties of sealing materials and surfaces

Sealing material
property

EPDM is the standard sealing material for the Hygenic

plus

version. The following table

shows a selection of various EPDM properties. Take this information into account when
planning your system.

Property

EPDM stability

Alkali resistance

Very good

Resistance to ageing

Very good

Ammonia (no water)

Very good

Ethanol

Very good

Gasoline resistance

Low

Vapor

Up to 130 °C

Hot water

Very good

Lye

Very good

Carbonic acid

Very good

Methanol

Very good

Sodium chloride

Very good

Oil (vegetable, ethereal)

Good to medium

Oil and grease resistance

Low

Ozone resistance

Very good

Phosphoric acid (50 %)

Very good

Nitric acid (40 %)

Good

Hydrochloric acid (38 %)

Very good

Acid resistance

Very good

Sulfuric acid (30 %)

Very good

Silicone oils and greases

Very good

Drinking water

Very good

Suds (laundry detergent)

Very good

Sugar (watery)

Very good

Permitted temperature range

–25 ... +150 °C

NOTES

The low rated stability of EPDM in case of contact with mineral oils, gasoline, grease
etc. results from the fact that EPDM swells when it comes into contact with these mate-
rials. However, these chemicals do not destroy EPDM.

kVA

Summary of Contents for MOVIFIT SC series





















































































































































Search results

Summary of Contents for MOVIFIT SC series

Reviews:

Related manuals for MOVIFIT SC series

Brands by name

Popular brands

SEW MOVIFIT SC series, Operating Instructions Manual

Search results

Summary of Contents for MOVIFIT SC series

Reviews:

Related manuals for MOVIFIT SC series

Brands by name

Popular brands