SES SE-2040-2 User Manual Download Page 4

 

 
 

SEALED ENERGY SYSTEMS

®

 

User Manual  

      

The  battery  pack  comprises  the  individual  elements  as  shown 
below: 

 
 
 
 
 

 
 
 
 
 
 
 
 

 

2.3 

General Precaution 

 

2.3.1  Handling 

 

 

Avoid shorting the battery. Do not immerse in water. 

 

Do not disassemble or deform the battery 

 

Do not expose to, or dispose of the battery in fire. 

 

Avoid excessive physical shock or vibration. 

 

Keep out of the reach of children. 

 

Avoid storage in direct sunlight. 

 

Do not short-circuit a battery. 

 

In the event of a battery leaking, do not allow the liquid to 
come  in  contact  with  the  skin  or  eyes.  If  contact  has  been 
made, wash the affected area with copious amounts of water 
and seek medical advice. Keep batteries clean and dry. 

 

Secondary batteries need to be charged before use. 

 

When  possible,  remove  the  battery  from  the  equipment 
when not in use. 

 

Do  not  store  batteries  longer  than  1  month  in  discharged 
state.  Do  not  storage  batteries  longer  than  1  year  without 
recharge. 

 

2.3.2  Charge & Discharge 

 

 

Battery must be charged in appropriate charger only. 

 

Never use a modified or damaged charger. 

 

Specified product use only. 

 

Operating Temperature  

 

For Charge: 0

O

C to +45

O

 

For Discharge: -20

O

C to +55

O

 

2.3.3  Storage 

 

 

Store in a cool, dry and well-ventilated area. 

 

Storage Temperature: -20

O

C to +45

O

 

Recommender Storage Temperature 20

O

C + 5

O

 

Summary of Contents for SE-2040-2

























Reviews: