background image

 

 
 

SEALED ENERGY SYSTEMS

®

 

User Manual  

      

Taiwan: 

Expended  battery  packs  are  not  considered  hazardous 
waste.  Cells  and  batteries  should  be  recycled  at  an 
appropriate  collection  site  in  accordance  with 
government regulations.  

Japan: 

Recycling  of  expended  lithium-ion  battery  packs  is 
regulated  by  the  Wastes  Disposal  and  Public  Cleaning 
Law and the Law for Promotion of Effective Utilization.  

Brazil:

 

Expended  battery  packs  should  be  recycled  in 
accordance  to  the  Natation  Solid  Waste  Policy  (PNRS) 
or  CONAMA  in  compliance  with  the  directives  and 
regulations  of  the  National  System  of  Environmental 
(SISNAMA). 

Malaysia: 

Lithium-ion  cells  and  batteries  are  considered 
scheduled  wastes  and  must  be  sent  to  a  proper 
collection  treatment,  recycling  and  Disposal  Centre; 
Scheduled Waste Code SW103. 

Classification  of  Waste  to  comply  with  Transport  Regulations: 
Expended Lithium-Ion Battery packs are not considered hazardous 
waste.  Lithium-ion  battery  packs  that  have  been  involved  in  a  fire 
maybe  considered  hazardous  waste  and  should  be  marked  and 
classified as such.  

Classification  of  Waste  Packaging  Material:  Under  normal  use 
packaging is not consider hazardous and should be disposed of in 
accordance  with  local  recycling  regulations.  Packaging  that  has 
been  exposed  to  a  damaged  leaking  cell  should  be  considered 

hazardous waste and disposed of in accordance to local rules and 
regulations. 

 

 

3  REQUIREMENTS 

 
3.1 

General Requirements  

 

3.1.1.  Nominal Voltage 

 

The battery nominal operating voltage is 10.8V 

 

3.1.2.  Rated Capacity 

 

The  initial  capacity  is  8550mAh  (based  on  a  CV  charge  of 

12.6V±50mV  with  a  current  limit  of  4350mA  and  6000mA 
discharge to 8.55V @ 25C, within 1 hour of charge). 

 

3.1.3.  Initial Impedance 

 

The  internal  impedance  of  a  fully  charged  battery  shall  be 

≤1

45m

  when  measured  across  the  positive  and  negative 

battery terminals at 1kHz at 20°C. 
 

Summary of Contents for SE-2020

























Reviews: