and you maybe have to place the sensor directly
7.2 Fishing on ice
To achieve fishing on ice availability.It is highly
twisting motion(fig-21.)
Note:
If depth readings appear as "---"while
press it against the hull bottom with a
the sonar sensor with petroleum jelly. and
suggested that you cut a hole through the ice
suggested that you keep the unit in temperatures
above 0 degrees Fahrenheit(-18 degrees Celsius)
during operation.Remove the batteries from the
fish finder to prevent battery leakage and
Temperature unit setting is the switch of
to float on the surface(Fig-19).
submerge or spray the fish finder screen
housing with water or use chemical to clean.
corrosion.Clean the sonar sensor and cable with
fresh water and dry it off before storing.Do not
this may cause damage to the sensitive internal
Cold weather is extremely hard on the electrical
components within the display housing .It is
sonar sensor and ice,or the water below the ice,
and place the sonar sensor into the water directly
(fig-22).If you would like to check the area for
depth or fish before cutting a hole.Clear away
the snow from ice surface,making sure the
the unit will not work properly and will require to
surface is smoolth.Place a small amount of liquid
temperature unit.
7.1.2Attach the adapter to the boat hull
until "Depth unit"is displayed on the screen(fig-
press and release the "MENU"key,
13).Through left/right key to adjust depth unit.
(-20
℃
-70
℃）
7.1.3"shoot- Thru" the hull of a boat. Place
7.1 Fishing at the boat
7.Fishing at the boat or on ice
7.1.1Toss the sensor and float into the water
Operational
. 12.
White - LED
Depth range Max: 73M/240Feet
Power: 4-AAA alkaline batterie
Measure unit:
feet /meter
Sensor beam angle: 45 degrees
8.Product specification
. 9 .
adjust fish Icon on/off.
key, until "Fish Icon"is displayed on the
as the previous instructions.
using the mounting tabs.
temperature unit.
. 13 .
. 14 .
5)Neck strap.
6)product specification
3)Stainless Bolt
4)Stainless wring nut
1)Round transducer with 25ft cable
2)Transducer adapter
9.Attachments:
Depth range Min: 0.6M/2 Feet
Display: FSTN - LCD
Backlighting:
. 16 .
"Chart Speed" is adjust the screen scan
screen(fig-11). Through left/right key to
speed.The unit have 4 grades("4" is the fast).
. 15 .
Temperature:
hand.If it will not come loose,sprinkle a small
ice ,tap sonar sensor gently at the base by your
electronics.
amount of water on the ice surface around the
base and repeat such actions until the sonar
sensor is easily moved.
Never use a blunt to strike the sonar sensor as
try another spot or cut a hole in the ice to use.
Note:
To remove the sonar sensor from the freeze
press and release the "MENU"
Operation:
5.8 Chart Speed setting
press and release the "MENU"
Operation:
key, until "Chart speed"is displayed on the
screen(fig-12), Through left/right key to
adjust scan speed.
Operation:
5.9.Depth unit setting
Depth unit setting is the switch of depth unit.
5.10 Temperature unit setting
until "Temperature unit" is displayed on the
press and release the "MENU"key,
screen (fig-14).Through left/right key to adjust
Operation:
6.Fixing Sonar Sensor
6.1
Pull out the rubber stopper,adjust float so that
desired depth.Replace the rubber stopper by
it is 20 to 30cm away from the sensor,or at your
pressing it firmly into the float.The Sensor float
must be adjusted so that It is a minimum of 20cm
away from the sensor(fig-15)
desirable position(Fig-18)or add floats on the cable
6.4
Use a pole to guide the sonar sensor to a
Place the sonar sensor and float in your hand,and
into water at your desired fishing location.To toss,
pitch underhand.Do not throw the cable, as this
6.2
Toss the sonar sensor and float assembly
maybe cause unrepairable
wrapped aroud anything.
6.3 Your fish finder includes
is removable and adjustable up to 180 degrees.
sensor in a new location in the hull.and repeat
method 7.1.3. If it still does not work on all hull
cable by siding and gently pulling the float
need it.Remove the rubber stopper from the
(fig-23).If there are any air bladder between the
water allowing the water freeze around the unit
finder is operating properly. If it operates properly
while directly in the water.Reposition the sonar
debris (fig-20).The float can be removed
from the cable. If you find that you do not
out off the cable toward the plug.
boat hull (fig-17).and appropriate rod.The adapter
sensor directly in the water to verify that the fish
to sink into the bottom ,It maybe entangled
using one of these methods.Place the sonar
Note:Incorrect using.Do not allow the cable
taps so that you can attach it to any flat surface or
sonar sensor(fig-16).The adapter includes mounting
a combination adapter,mounting bracket for the
Before tossing,be sure that the cable
damage.
is free from tangle and is not
. 10 .
. 11 .
into the water for proper operation.
water on the ice.then set the sonar sensor on the
