SEPTENTRIO AsteRx4 Hardware Manual Download Page 22 | Manualshive

Page: 22 / 26

background image

2
2

2

AsteRx4 Evaluation Kit

22

Name printed
on the board

Pin of the 80-pin connector Function

REF_PIO

Pin#39

These pins are tied together in the
interface board. The signal on these pins
is the 10-MHz frequency reference.

REF_I_PIO

Pin#43

EVENT_A

Pin#34

First event marker (input)

EVENT_B

Pin#35

Second event marker (input)

PPSO

Pin#38

PPS output signal (output)

The left pins of this header are all tied to ground.

3.4.4

Serial Connectors

Electrical levels conform to the RS232 standard. RTS/CTS lines are supported only on
COM2 and COM3. Connection to a PC is done through a null-modem cable.

3.4.5

USB Connector

By default, the USB interface is configured in full speed mode (USB 1.1, 12 Mbps). See
also section 2.8.

Note that it is not possible to power the interface board through the USB connector.

3.4.6

Ethernet Connector

This RJ45 socket allows 10/100 Base-T Ethernet communication to the AsteRx4_OEM
board.

COM 4

COM 1

COM 3

COM 2

«
...
20
21
22
23
24
...
»

Summary of Contents for AsteRx4



























Reviews:

No comments

Related manuals for AsteRx4

Brand: Handic Pages: 21

Brand: Panasonic Pages: 10

CQCM130U - MP3 CD RECEIVER

Brand: Panasonic Pages: 2

CQC800U - AUTO RADIO/CD DECK

Brand: Panasonic Pages: 38

CQC800U - AUTO RADIO/CD DECK

Brand: Panasonic Pages: 24

CQC500U - CD Receiver With Changer Control

Brand: Panasonic Pages: 8

CQC1304U - AUTO RADIO/CD DECK

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 30

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 48

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 2

CQVX100U - Car Audio - DVD Receiver

Brand: Panasonic Pages: 24

CQDFX403U - AUTO RADIO/CD DECK

Brand: Panasonic Pages: 5

Brand: Panasonic Pages: 20

CQC1103U - AUTO RADIO/CD DECK

Brand: Panasonic Pages: 16

CQCP134U - AUTO RADIO/CD DECK

Brand: Panasonic Pages: 16

MultiView II DVI-Rx-1K

Brand: Magenta Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands