manualshive.com logo in svg

Sentry VREL, Installation, Operation & Maintenance Manual, Page: 3 / 12

Share
Download
Sentry VREL Installation, Operation & Maintenance Manual Download Page 3

Sentry VREL Control Valve 3

Safety Information

Please read the entire manual before attempting to unpack, set up, or operate this 

product. Pay careful attention to all Warnings, Cautions, and Notes. Failure to do so could 

result in serious personal injury and/or equipment damage.

Use of Hazard Information

If multiple hazards exist, the signal word corresponding to the greatest hazard shall be 

used.

Defi nitions

DANGER

 indicates a hazardous situation 

which, if not avoided, will result in death or 

serious injury .

WARNING

 indicates a hazardous situation 

which, if not avoided, could result in death or 

serious injury .

CAUTION

, used with the safety alert symbol, 

indicates a hazardous situation which, if not 

avoided, could result in minor or moderate 

injury .

NOTICE

 is used to address practices not 

related to personal injury .

 

Â

NOTE

Information that requires special emphasis .

 

Â

TIP

Alternate techniques or clarifying information.

SHALL: 

This word is understood to be mandatory.

SHOULD: 

This word is understood to be advisory.

Summary of Contents for VREL













Reviews:

No comments