manualshive.com logo in svg

Sentry US ACSK-EM, Instruction Manual, Page: 3 / 16

Share
Download
Sentry US ACSK-EM Instruction Manual Download Page 3

Copyright © 2010-2011. All rights reserved.

 

3

 R082011-V03 

www.SentryUS.com 

 

Keypad Description 

 

 

Mounting Installation 

 

(

Note:  Before mounting, decide first where to mount the keypad

.) 

 

1.  Open the control keypad by removing the screw at the bottom using the 

provided torque wrench. 

2.  Punch the necessary holes at the back template for the screws. 
3.  Using the back template as a guide, drill the holes for the screws and system 

wiring (make a bigger hole for the system wiring). 

Note: Level the back template 

4.  Draw out the system wiring through the center hole of the back template. 
5.  Mount the back template using the screws provided. 
6.  Mount the front panel using the torque wrench. 
7.  Connect system wiring (see System Wiring Diagram and System Wiring 

Connections). 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

No. 

Description 

 

Mode Indicators 

Yellow, Red, Green 

 

Door Indicators 

 

Antenna 

 

Matrix Keypad 

 

Vandal Proof Case Screw 

 

Summary of Contents for ACSK-EM

















Reviews:

No comments