Assembly Instructions For Sentimental Me, Inc. Memorabilia Storage Box
Video Assembly Instructions:
For a video which demonstrates how to assemble the storage box, please go to the
sentimentalmeboxes.com
website and click on the Video Box Assembly link at the bottom of the website’s Home Page. We highly recommend
that you watch the assembly instructions video before and while you are assembling the storage box. The written assembly instructions below are very detailed and might vary with the assembly instructions video in certain respects because there is more than
one way to assemble some of the box parts. The purpose of the assembly instructions video is to give our customers additional assistance in assembling the storage box.
Written Assembly Instructions:
Separate the identical box parts in piles on a flat working surface and make sure you have the correct number of parts. Included are the following: one (1) Box Bottom; one (1) Box Top; one (1) Box Liner; one (1) Large Open
Slip Case; one (1) Small Open Slip Case; two (2) Large Interior Boxes; four (4) Medium Interior Boxes; five (5) Small Interior Boxes; and one (1) Tray having one (1) Tray Body, (1) Long Tray Divider and two (2) Small Tray Dividers. Before assembling each
part of the box, please notice that there are creases in each part except the Box Bottom.
Please slightly and partially fold each part very carefully along the crease lines to make assembly easier
. There might be some noticeable perforated “excess”
cardboard pieces in certain parts that will not be used and must be punched out by hand. Also, certain parts might be slightly attached together by cardboard (especially the Tray parts), and must be pulled apart by hand. Please follow the directions listed below
with each part illustration
. In the unlikely event any part of the box becomes unglued, please apply a generous amount of Gorilla Super Glue to the affected area to repair. You might also apply Gorilla Super Glue in appropriate areas to the Box
Bottom, Box Top and Box Liner to further strengthen such parts’ connections.
Box Bottom
Box Top
Place the Box Bottom upright as shown on a working surface. Push the sides inward and the Box Bottom will lock into
place. With the Box Bottom locked into place, roll over the top panels on all sides of the Box Bottom into the Box Bottom
as far as they will go, with the panels on the sides above the handle openings being rolled first. If they don’t lock into
place, don’t worry because the Box Liner when inserted in the Box Bottom will keep such top panels securely against the
sides of the Box Bottom.
Fold over the flanges on the short sides of the part until they meet the Box Top’s main body. Then, roll the panels on the long
sides of the Box Top over the flanges and lock them into place. After the panels on the long sides of the Box Top are locked
into place, roll over the panels on the short sides of the Box Top to complete the set up. The diagonal cuts on the corners will
lock the Box Top’s side panels into place.
Box Liner
Large and Small Open Slip Cases
Fold the panels of the Box Liner until the outer panels meet. Please make sure that the bottom piece attached to the long
side of the Box Liner stays above the bottom pieces attached to the short sides of the Box Liner having handle openings.
Insert the Box Liner as shown above into the Box Bottom.
Lay the parts flat as shown. Make sure the four (4) flanges attached to the part’s sides are bent and loosened up. While keeping
the bottom of the part sitting on the flat surface you are working on, slowly lift upward the side panels of the part. The two (2)
smaller flanges should sit on top of the part’s bottom and the two (2) larger flanges should sit on top of the two (2) smaller
flanges and the pieces when closed together should form a rectangular shape with only the two (2) tabs extending beyond the
sides of the part. Now, lock both tabs into the openings on the part’s sides. While the part is sitting in an upright position, roll
over the top flaps on the short ends of the part into the box. Please notice there are notches cut into the flaps on the short ends
of the part and tabs extending from the flaps on the long sides of the part. Now, roll over the top flaps on the long sides of the
part and lock their tabs into the notches cut into the flaps on the short ends of the part. Insert both Open Slip Cases into the Box
Bottom, one on each side.
