background image

www.sentera.eu

MIW-DCVCX-R-EN-000 - 29 / 06 / 2021

4 - 10

back to the table of contents

DCVCX-R

 

INTELLIGENT AIR QUALITY 
DUCT  SENSOR

PRODUCT DESCRIPTION

The DCVCX-R are intelligent duct sensors featuring adjustable temperature, relative 
humidity and TVOC ranges. The used algorithm controls a single analogue/modulating 
output based on the measured temperature, relative humidity and air quality values, 
which can be used to directly control an EC fan, an AC fan speed controller or an 
actuator powered damper. All parameters are accessible via Modbus RTU. 

ARTICLE CODE

Article code

Supply

Imax

DCVCG-R

18—34 VDC 

45 mA

15—24 VAC ±10% 

50 mA

DCVCF-R

18—34 VDC

45 mA

INTENDED AREA OF USE

 

 Demand controlled ventilation based on temperature, relative humidity and TVOC 

 

Suitable for mounting in air ducts

TECHNICAL DATA

 

Analogue / modulating output type:

 

0—10 VDC mode: R

L

 ≥ 50 kΩ

 

0—20 mA mode: R

L

 ≤ 500 Ω)

 

 PWM (open-collector type) mode: PWM Frequency: 1 kHz, R

L

 ≥ 50 kΩ; PWM 

voltage level 3,3 VDC or 12 VDC

 

Replaceable TVOC sensor module

 

Selectable temperature range: -30—70 °C

 

Selectable relative humidity range: 0—100 % rH

 

Selectable ТVOC range: 0—60.000 ppb

 

Warm-up time: 15 minutes

 

Accuracy: ±0,4 °C (-30—70 °C); ±3 % rH (0—100 % rH); ±15% TVOC (0—60.000 ppb) 

 

Minimum airflow velocity required: 1 m/s

 

Enclosure and probe material:

 

ASA, grey (RAL9002)

 

Protection standard: enclosure: IP54, probe: IP20

 

Operating ambient conditions:

 

temperature: -30—70 °C

 

rel. humidity: 0—100 % rH, (non-condensing)

 

Storage temperature: -10—60 °C

STANDARDS

 

Low Voltage Directive 2014/35/EC

 

 

EN 60529:1991 Degrees of protection provided by enclosures 

 

(IP Code) Amendment AC:1993 to EN 60529

 

 EN 60730-1:2011 Automatic electrical controls for household and similar use - 
Part 1: General requirements

 

EMC Directive 2014/30/EC

 

 EN 60730-1:2011 Automatic electrical controls for household and similar use - 
Part 1: General requirements

 

 EN 61000-6-1:2007 Electromagnetic compatibility (EMC) - Part 6-1: Generic 
standards - Immunity for residential, commercial and light-industrial environments

 

 EN 61000-6-3:2007 Electromagnetic compatibility (EMC) - Part 6-3: Generic 
standards - Emission standard for residential, commercial and light-industrial 
environments Amendments A1:2011 and AC:2012 to EN 61000-6-3

Summary of Contents for DCVCX-R











Reviews: