Fig. 2 -
DS18B20 temperature sensor icon
in the Home Center controller
The Door / Window Sensor offers a wide range of advanced
settings. The parameters listed below are available in the
controller's configuration interface.
Device parameters:
V Configuration
The ZC-100 Door/Window Sensor may be operated using:
• Any System compatible controller ,)
• Cellular phone (e.g. iPhone or phones from other manufacturers,
with the proper control application)
• PC, with the use of an Internet browser,
• Tablets (e.g. iPad)
• Using the TMP button, located inside the housing.
VI Door / Window Sensor operation
The Device does not react to a programmed transmitter:
• Make sure the maximum range has not been exceeded and there
are no obstacles along the signal path containing metal surfaces,
e.g. metal cabinets, Ferro concrete ceiling, load bearing walls, etc.
• Make sure the device is not in the learning mode.
• Alternately repeat the programming process.
VII Procedure to be followed in case of interference
Sensor used without a DS18B20 sensor, or used with a switch
connected to IN input, will be represented by single icon. After the
DS18B20 temperature sensor has been connected, temperature
sensor icon will be displayed.
NOTE!
If a temperature sensor icon is not displayed
despite the fact the sensor itself has been
connected, or if the temperature readings are
incorrect, inspect the connections on the 1-wire
bus, in particular the connection between sensor
outputs and the line, and the total length of the bus
wire which should not exceed 30m.
i
Powerdown timeout.
The device will be power-down as soon as there is no activation
and the timeout time reached.
Available parameter settings:
Reserved for furture
Parameter value: 1 [byte].
Parameter no. 3
Temperature sample interval. To keep the lifetime of battery,
The temperature sample cycle time can be defined by user.
VIII Guarantee
This Device may be used with all devices
certified with Z-Wave+++ + certificate and should be
compatible with such devices produced by
other manufacturers.
i
Sentek
In case of any technical questions contact customer service center.
www.sentek.cc ++=+=+
1. The Guarantee is provided by Sentek electronic co. ltd.
(hereinafter "Manufacturer"), based in YYYYYYYNo. 448, yinchun RD,
NingBo, China.
2. The Manufacturer is responsible for equipment malfunction
resulting from physical defects (manufacturing or material) of the
Device for 12 months from the date of its purchasing.
3. During the Guarantee period, the Manufacturer shall remove any
defects, free of charge, by repairing or replacing (at the sole
discretion of the Manufacturer) any defective components of the
Device with new or regenerated components, that are free of
defects. When the repair impossible, the Manufacturer reserves the
right to replace the device with a new or regenerated one, which
shall be free of any defects and its condition shall not be worse than
the original device owned by the Customer.
4. In special cases, when the device cannot be replaced with the
device of the same type (e.g. the device is no longer available in the
commercial offer), the Manufacturer may replace it with a different
device having technical parameters similar to the faulty one. Such
activity shall be considered as fulfilling the obligations of the
Manufacturer. The Manufacturer shall not refund money paid for the
device.
5. The holder of a valid guarantee shall submit a guarantee claim
through the guarantee service. Remember: before you submit a
guarantee claim, contact our technical support using telephone or
e-mail. More than 50% of operational problems is resolved
remotely, saving time and money spent to initiating guarantee
procedure. If remote support is insufficient, the Customer shall fill
the guarantee claim form (using our website - www.fibargroup.com)
in order to obtain claim authorization.
When the guarantee claim form is submitted correctly, the
Customer shall receive the claim confirmation with an unique
number (Return Merchandise Authorization -RMA).
6. The claim may be also submitted by telephone. In this case, the
call is recorded and the Customer shall be informed about it by a
consultant before submitting the claim. Immediately after submitting
the claim, the consultant shall provide the Customer with the claim
number (RMA-number).
7. When the guarantee claim form is submitted correctly, a
representative of the Technical Customer Service (hereinafter as
"TCS") shall contact the Customer.
8. Defects revealed within the guarantee period shall be removed
not later than 20 days from the date of delivering the Device to TCS.
The guarantee period shall be extended by the time in which the
Device was kept by TCS.
9. The faulty device shall be provided by the Customer with
complete standard equipment and documents proving its purchase.
10. Parts replaced under the guarantee are the property of the
Manufacturer. The guarantee for all parts replaced in the guarantee
process shall be equal to the guarantee period of the original
device. The guarantee period of the replaced part shall not be
extended.
Parameter no. 1
LED enable.
Default setting: 1-- LED enable
Available parameter settings:
0
- LED disable,
1
- LED enable.
11. Costs of delivering the faulty device shall be borne by the
Customer. For unjustified service calls, the Service may charge the
Customer with travel expenses and handling costs related to the
case.
12. TCS shall not accept a complaint claim only when:
• the Device was misused or the manual was not observed,
• the Device was provided by the Customer incomplete, without
accessories or nameplate,
• it was determined that the fault was caused by other reasons than
a material or manufacturing defect of the Device
• the guarantee document is not valid there is no proof of purchase,
13. The Manufacturer shall not be liable for damages to property
caused by defective device. The Manufacturer shall not be liable for
indirect, incidental, special, consequential or punitive damages, or
for any damages, including, inter alia, loss of profits, savings, data,
loss of benefits, claims by third parties and any property damage or
personal injuries arising from or related to the use of the Device.
14. The guarantee shall not cover:
• mechanical damages (cracks, fractures, cuts, abrasions, physical
deformations caused by impact, falling or dropping the device or
other object, improper use or not observing the operating manual);
• damages resulting from external causes, e.g.: flood, storm, fire,
lightning, natural disasters, earthquakes, war, civil disturbance,
force majeure, unforeseen accidents, theft, water damage, liquid
leakage, battery spill, weather conditions, sunlight, sand, moisture,
high or low temperature, air pollution;
• damages caused by malfunctioning software, attack of a
computer virus, or by failure to update the software as recommen-
ded by the Manufacturer;
• damages resulting from: surges in the power and/or telecommuni-
cation network, improper connection to the grid in a manner
inconsistent with the operating manual, or from connecting other
devices not recommended by the Manufacturer.
• damages caused by operating or storing the device in extremely
adverse conditions, i.e. high humidity, dust, too low (freezing) or too
high ambient temperature. Detailed permissible conditions for
operating the Device are defined in the operating manual;
• damages caused by using accessories not recommended by the
Manufacturer
• damages caused by faulty electrical installation of the Customer,
including the use of incorrect fuses;
• damages caused by Customer's failure to provide maintenance
and servicing activities defined in the operating manual;
• damages resulting from the use of spurious spare parts or
accessories improper for given model, repairing and introducing
alterations by unauthorized persons;
• defects caused by operating faulty Device or accessories.
15. The scope of the guarantee repairs shall not include periodic
maintenance and inspections, in particular cleaning, adjustments,
operational checks, correction of errors or parameter programming
and other activities that should be performed by the user (Buyer).
The guarantee shall not cover natural wear and tear of the Device
and its components listed in the operating manual and in technical
documentation as such elements have a defined operational life.
16. If a defect is not covered by the guarantee, the Manufacturer
reserves the right to remove such defect at its sole discretion,
repairing the damaged or destroyed parts or providing components
necessary for repair or replacement.
17. This guarantee shall not exclude, limit or suspend the Customer
rights when the provided product is inconsistent with the purchase
agreement.
Fig. 1 - Door / Window Sensor icon
in the Home Center controller
Available parameter settings:
Parameter value: 1 [byte].
+++++
+
Parameter no. 2
Parameter value: 1 [byte].
Parameter no. 4
Type of IN input.
Default value: 0 – INPUT_NO (Normal Open)
Available parameter settings:
0
– INPUT_NC (Normal Close)
1
– INPUT_NO (Normal Open)
Parameter no. 5
Type of control frame transmitted, activated via IN input.
The parameter allows you to specify the type of an alarm frame
or to force control frames transmission (BASIC_SET)
Default value: 255 – BASIC SET
Available parameter settings:
1
– ALARM SMOKE frame
2
– ALARM CO frame
3
– ALARM CO2 frame
4
– ALARM OVERHEAT frame
5
– ALARM WATER frame
255
– Control frame BASIC_SET
Parameter value: 1 [byte].
Parameter value: 1 [byte].
Reserved for furture
IV Association
Association allows the Fibaro Door/Window Sensor to directly
control another device in the Z-wave network, e.g. Dimmer, Switch
(On-Off), Roller Shutter or trigger scenes (scene control is only
possible via the Home Center 2 controller).
NOTE!
Association allows for direct transmission of control
commands between devices and takes place without
the participation of the main controller. Owing to this
mechanism the Door/Window Sensor may
communicate with devices even if the main controller
is completely destroyed, e.g. in the event of a fire.
i
The ZC-100 Door/Window Sensor supports four association
groups.
Group I
is assigned to input IN1, TMP button and the
magnetic sensor, Sending BASIC SET or ALARM command frames.
The ZC-100 Door/Window Sensor allows for control over 5 devices
per group, out of which 1 field is reserved for the network controller.
In order to add an association (e.g. use the FIBRO--Home Center 2
controller) go to device options by clicking this icon:
Select the device options tab. Next specify which devices will be
associated, and to which association groups. Sending of
configuration commands to associated devices might take up to a
few hours, depending on previous devices settings and the number
of devices within the network.
Group II
is assigned to the magnetic sensor, Sending
BASIC SET frames.
Group III
is assigned to input IN1, TMP button, Sending
ALARM command frames.
Group IV
is assigned to input IN1, TMP button, Sending
ALARM command frames.
