manualshive.com logo in svg

Sentec SDM, Service Manual

Share
Download
Sentec SDM Service Manual Download Page 81

 

5 Repairs of the SDM 

 

 

SenTec Digital Monitoring System 

 

 

 

75 

5.3

 

Replacement, Silicon Foot 

 

1.

 

Follow the procedure described in 

section 

5.1

 "Prior to Repair". 

2.

 

Clean  the  groove  for  the  silicon  foot  with  a  cotton  swap  soaked  with  70% 
isopropanol. 

3.

 

Put  one  drop  of  silicon  glue  (see

  section 

8.2

  “Testing  Accessories  and  Spare 

Parts”) in the groove. 

4.

 

Insert the new silicon foot into the groove by pressing firmly. 

5.

 

Allow the glue to dry. 

 

 

Figure 13  Replacement, Silicon Foot 

 

5.4

 

Replacement, main fuses 

 

1.

 

Follow the procedure described in 

section 

5.1

 "Prior to Repair". 

2.

 

Remove the fuse holder from the AC Power Connector by compressing the two tabs 
on  both  sides  of  the  lid  and  pulling  out  the  fuse  holder  according  to 

Figure 14

  Replacement, Main Fuses. 

3.

 

Replace the defective fuses with time delay, high breaking capacity fuses, by fuses 
with rated current as specified on the SDM rear panel (see section 8.2 “Testing 
Accessories and Spare Parts”) 

4.

 

Reinsert the holder into the AC Power Connector. 

 

Fuse drawer 

 

Figure 14  Replacement, Main Fuses 

Summary of Contents for SDM






























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands