manualshive.com logo in svg

Sentec SDM, Service Manual

Share
Download
Sentec SDM Service Manual Download Page 65

 

4 Troubleshooting 

 

 

SenTec Digital Monitoring System 

 

 

 

59 

Problem 

Possible Cause(s) 

Recommended action(s) 

PO2-module error 
detected 

General PO2-module error detected (e.g. off-
centered white spot missing). 
The sensor can still be used for monitoring of 

the  other  parameters  but  PO2.  Replace 
OxiVenT™  Sensor  if  you  wish  to  continue 
monitoring PO2. 
Note: In this case the SDM should display 
the message ‘Sensor problem 73’ (see 

Technical Manual for the SDM). 

 
 

 

4.2.4

 

SDM specific troubleshooting 

Table 9 

SDM specific troubleshooting 

Problem 

Possible Cause(s) 

Recommended action(s) 

P0400 

SDM not 

operational, 
SDM LEDs 
not 
illuminated

 

SDM switched off   Switch on SDM. 
SDM not connected 
to mains and 
battery depleted 

Connect the SDM to the mains. Allow battery 
to charge. 

Mains power supply 
defective 

Choose another mains power supply for 
connecting the SDM. 

SDM defective 
 

Switch the SDM off and on again. 
If problem persists contact qualified service 
personnel. 

Main fuses 
defective 

Replace main fuses according to section 5.4 
Replacement, main fuses. 

SDM defective 

Contact SenTec authorized service personnel. 

AC/DC Power 
Supply not 
connected 

Connect AC/DC Power Supply according to 
the 

Repair Manual for the SDMS. 

 

 

To be performed by SenTec authorized 

service technicians only.

 

AC/DC Power 
Supply defective 

Replace AC/DC Power Supply according to 
the 

Repair Manual for the SDMS. 

 

 

To be performed by SenTec authorized 

service technicians only.

 

Summary of Contents for SDM






























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands