SENSORWORX SWX-852-B Series Installation & Operation Instructions Download Page 2

 

Ã

The switch/dimmer runs on one CR123(A) Lithium Battery (included).

 

Ã

Install battery prior to mounting. Polarity is indicated on the battery compartment 
door.

 

Ã

If the unit’s battery life reaches 10%, the LED will rapidly blink blue after every 
button press.

 

Ã

Replacement batteries are available at most retailers or home centers where 
batteries are sold or from 

SENSOR

WORX.

BATTERY INFORMATION

COMPATIBLE WIRELESS DEVICES

The below chart lists the devices that can be used in a 

SENSOR

WORX wireless application. Note that sensors and remote switch & dimmer devices are transmit only devices and 

therefore must be linked to a load controller for switching or dimming of lighting.

MODEL #

DESCRIPTION

WIRELESS TYPE

POWER TYPE

SWX-201-B 

Small Motion 360° Sensor, PIR

Transmit

Battery

SWX-401-B

Wide View Sensor, PIR

Transmit

Battery

SWX-402-B

Long Range Hallway Sensor, PIR

Transmit

Battery

SWX-851-xx

Wall Switch Load Controller, No Neutral Required, <xx = color>

Transmit & Receive

120-277 VAC

SWX-852-B-xx

Remote Switch (On/Off), <xx = color>

Transmit

Battery

SWX-854-B-xx

Remote Dimming Switch (On/Off, Raise/Lower), <xx = color>

Transmit

Battery

SWX-950

Power Pack Load Controller, 20A

Receive

120/277 VAC

SWX-950-D2

Power Pack Load Controller, 20A, 0-10V Dimming

Receive

120/277 VAC

SWX-950-AX

Hybrid Wireless/Wired Power Pack Load Controller, 20A

Transmit & Receive

120/277 VAC

SWX-950-AX-D2

Hybrid Wireless/Wired Power Pack Load Controller, 20A, 0-10V Dimming

Transmit & Receive

120/277 VAC

MOUNTING

BRACKET

CHASE NIPPLE

BATTERY

COMPARTMENT

BATTERY

COMPARTMENT

BATTERY

COMPARTMENT

LOCK NUT

CHASE NIPPLE

LOCK NUT

LOCKING 3-POSITION

TILT ADJUSTMENT

MOUNTING

BRACKET

LOCKING 3-POSITION

TILT ADJUSTMENT

SERRATED END

FOR CUTTING

THROUGH

CEILING TILE

SERRATED END FOR CUTTING 

THROUGH CEILING TILE

INSTALLATION INSTRUCTIONS

 

Ã

Designed to mount in 1-gang wall box with 3.28” hole spacing.

 

Ã

Units can also share multiple gang wall boxes with other devices.

LED INDICATOR

LED INDICATOR

DIMMING UP

DIMMING DOWN

ON BUTTON

OFF BUTTON

ON BUTTON

OFF BUTTON

LED INDICATOR

LED INDICATOR

DIMMING UP

DIMMING DOWN

ON BUTTON

OFF BUTTON

ON BUTTON

OFF BUTTON

SWX-852

SWX-854

OPERATION NOTES

 

Ã

Wireless remote switches and dimmers only transmit when a button is being pressed.

 

Ã

The unit’s blue LED will light only when a button is pressed.

 

Ã

The dim up and dim down buttons may be held down to increase dimming rate.

Summary of Contents for SWX-852-B Series

Page 1: ...manual operation of wirelessly controlled lighting These attractive wall stations greatly reduce total installation time and wireless pairing fuss Requiring just a few seconds per device SENSORWORX wireless sensors can be linked to one or more wireless load controllers such as the SWX 851 wireless wall switch or a SWX 950 series wireless power pack Additionally these devices can be configured to w...

Page 2: ...e Switch On Off xx color Transmit Battery SWX 854 B xx Remote Dimming Switch On Off Raise Lower xx color Transmit Battery SWX 950 Power Pack Load Controller 20A Receive 120 277 VAC SWX 950 D2 Power Pack Load Controller 20A 0 10V Dimming Receive 120 277 VAC SWX 950 AX Hybrid Wireless Wired Power Pack Load Controller 20A Transmit Receive 120 277 VAC SWX 950 AX D2 Hybrid Wireless Wired Power Pack Loa...

Page 3: ...ng will also be automatically closed after 15 minutes of no new devices being linked Note 1 When in pairing mode the alternating LED colors on the wireless load controller will periodically pause and blink out the total number of paired devices There will be no blinks during the pause until the first device is linked CONFIGURATION MISC UNPAIRING FROM LINKED LOAD CONTROLLERS To unpair a wireless re...

Page 4: ...n If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different fr...

Reviews: