background image

SETTING #

DESCRIPTION

1

Test Mode

*

2

30 sec

3

5 min

4

10 min [Default]

5

15 min

6

20 min

7

30 min

CONFIGURATION SETTINGS

There are several settings that can be modified. To change a setting, follow 

the below steps:

1

  Press and hold the push button until blue LED begins flashing rapidly, then release.

2

  Tap the button the number of times corresponding to the Function # to be changed  

(e.g., 2 times for Time Delay).

3

  The LED will blink back white the number of times equal to the current setting  

(e.g., 4 times for 10 minutes). Following a short pause, this blink back sequence 
will repeat.

4

  Interrupt blink back by pressing the button the number of times corresponding to  

the new setting. (e.g., 3 times for 5 minutes). The LED will blink back white the 
number as confirmation.

5

  To exit and save, press and hold the push button until blue LED changes to white,  

then release. Unit will blink white twice indicating save was successful. If LED 
blinks twice blue, an error condition occurred.

FUNCTION #2 

OCCUPANCY TIME DELAY SETTINGS

Lights are held on following all occupancy events for the 
selected period.

* TEMPORARY 5 SEC TIME DELAY, REVERTS AFTER 10 MIN

INSTALLATION 

CONT.

MOUNTING

Ã

Ã

Designed to mount in 1-gang wall box with 3.28” hole spacing 

Ã

Ã

Units also can share multiple gang wall boxes with other devices

FRONT

SIDE

BREAK-OFF

BRACKET EARS

BREAK-OFF

BRACKET EARS

LED INDICATOR

BUTTON

SENSOR FACE**

2.74”

SUPPLIED MOUNTING SCREWS

FOR MOUNTING TO 

SINGLE GANG SWITCH BOX

1.39”

0.94”

1.69”

** SENSOR FACE IS FIELD REMOVABLE IN ORDER TO CHANGE COLORS. CONTACT FACTORY FOR ADDITIONAL FACES

KEY INSTALLATION 

FEATURE

25-40% SHALLOWER 
THAN OTHER WALL 
SWITCH SENSORS

** SENSOR FACE IS FIELD REMOVABLE IN ORDER TO CHANGE COLORS. CONTACT FACTORY FOR ADDITIONAL FACES

Summary of Contents for SWX-101 Series






Reviews: