Sensorex TX10 1/8 DIN Operation Manual Download Page 17

pg.

 

17

 

 

 

WARRANTY

 

 

Sensorex 

warrants this product to be free from significant deviations in material and 

workmanship for a period of 1 year from date of purchase. If repair or adjustment is 
necessary and has not been the result of abuse or misuse, within the year period, please 
return-freight-prepaid and the correction of the defect will be made free of charge. If you 
purchased the item from our 

Sensorex

 distributors and it is under warranty, please contact 

them to notify us of the situation. 

Sensorex 

Service Department alone will determine if the 

product problem is due to deviations or customer misuse. 
Out-of-warranty products will be repaired on a charge basis. 
 

RETURN OF ITEMS 

Authorization must be obtained from one of our representatives before returning items for 
any reason. When applying for authorization, have the model and serial number handy, 
including data regarding the reason for return. For your protection, items must be carefully 
packed to prevent damage in shipment and insured against possible damage or loss. 

Sensoex 

will not be responsible for damage resulting from careless or insufficient packing. A 

fee will be charged on all authorized returns. 

Note

 

:

 

Sensorex

 reserves the right to make improvements in design, construction and 

appearance of our products without notice

.

 

Summary of Contents for TX10 1/8 DIN


















Reviews: