Sensorex SD7500CD Product Instruction Sheet Download Page 1

Page 1 of 8  

Congratulations on your purchase of your Sensorex SD7000 

Series pH or ORP true differential electrode.  Please follow 

instructions and tips to get the maximum life out of your 

electrode.

Introduction

Electrode Care and Use Tips

1. The SD7000 Series pH and ORP electrodes are shipped with a  

    cap containing a solution of pH 4 buffer and potassium  

     

    chloride.  

    The cap should remain on the electrode until it is used. If the 

    electrode is used infrequently the cap and its solution should 

    be saved and the electrode stored in it. Store pH and ORP 

    electrodes in pH 4 buffer if soaking solution is discarded. 

    Before using the electrode remove the soaker cap as shown     

   in FIG 1.

2. Sensorex true differential electrodes have a 2 year prorated           

warranty from the date etched in the electrode body as shown         

   in FIG 2.   Electrodes in inventory should be rotated so that the      

    older electrodes are used first. The date code is stamped on 

each electrode by fiscal week and year (Example: 4613 = week 2    

of November 2013). 

3. After exposure to a sample, buffer or rinse solution, carryover 

    can be minimized by blotting—never by wiping—the elec-

    trode with a clean non-abrasive paper or a clean cloth towel. 

    

Do not use a brush on pH glass. 

4. As a rinse solution, measure and use a portion of the next 

    sample or buffer. This action will minimize carryover 

    contamination. 

5. When calibrating pH electrodes, use a buffer close in value to 

    that expected from the sample for one-point calibrations or as 

    the second buffer for two-point calibrations (See below). This 

    action will minimize span errors. ORP electrodes are typically 

    not calibrated. However, a solution to verify electrode perfor-

    mance should be used periodically. 225mV solution, Zobell's 

    solution (Part no. B225), is a good choice for single point 
    verification.

                                                                                                             

 PRODUCT INSTRUCTION SHEET 

Parts covered by this product data sheet include: 

SD7000CD, SD7000CD-ORP, SD7500CD, SD7500CD-ORP, SD7420CD, SD7420CD-ORP

    SD7000 Series Differential 
  pH/ORP Electrode Instructions

 FIG. 1

 FIG. 2

Form:  InstructSD7000CD-06 [Rev: 2016-10-10] 

 

Mo

de

l S

D7

00

0C

D D

iffe

ren

tia

l p

H

4615

Summary of Contents for SD7500CD









Reviews: