manualshive.com logo in svg

senseFly EBEE RTK, Extended User Manual

The senseFly EBEE RTK Extended User Manual is a comprehensive guide that provides in-depth instructions for operating and optimizing your EBEE RTK drone. Designed for easy access and understanding, this manual is available for free download from our website, allowing you to make the most of your product's capabilities.

Share
Download
background image

Manual control of the

eBee RTK

before Manual mode was enabled.

Caution:

We recommend that you only turn the remote control on

when it is held by a pilot ready to take manual control of the drone,
and that you turn it off when putting the remote control down.

Manual control of the

eBee RTK

can be achieved at any time if the drone is within

range of the remote⁴⁶.

FM: thrust
AM: speed

FM: ailerons

AM: turn rate

FM: elevator

AM: climb/sink rate

FM: Full Manual

AM: Assisted Manual

right stick

left stick

on: manual
off: auto

trim dials

Caution:

The remote control is preconfigured for use with the

eBee RTK

. In particular, the trim dials, used to finely adjust the position

of the drone’s ailerons, are calibrated to ensure optimal flight char-
acteristics and should not be adjusted. Changing the remote con-
trol’s configuration, including the trim settings, may compromise the
flight characteristics of the drone. If, for any reason, the preset set-
tings should be lost, contact your

eBee RTK

reseller.

⁴⁶ see section ‘Drone specifications’ on page 185 for the range of the remote control

141

Summary of Contents for EBEE RTK































































































































































































Reviews:

No comments

Related manuals for EBEE RTK

Wowitoys H4809C Manual preview
H4809C
Brand: Wowitoys Pages: 12
Autel EVO Max 4T Manual preview
EVO Max 4T
Brand: Autel Pages: 152
XAG M500 Remote Sensing UAS User Manual preview
M500 Remote Sensing UAS
Brand: XAG Pages: 28
Manta MDR003 SKY STIG User Manual preview
MDR003 SKY STIG
Brand: Manta Pages: 32
Cheerson CX-20 User Manual preview
CX-20
Brand: Cheerson Pages: 8
extreme fliers MICRO DRONE 3.0+ User Manual preview
MICRO DRONE 3.0+
Brand: extreme fliers Pages: 17
YUNEEC Typhoon H Calibration Manual preview
Typhoon H
Brand: YUNEEC Pages: 12
WowWee lumi 4448 User Manual preview
lumi 4448
Brand: WowWee Pages: 11
Carbonbird SCARAB YSiixkopta Manual preview
SCARAB YSiixkopta
Brand: Carbonbird Pages: 9
Rubicson 57687 Manual preview
57687
Brand: Rubicson Pages: 6
Contixo SC2 User Manual preview
SC2
Brand: Contixo Pages: 9
Contixo F10 Instruction Manual preview
F10
Brand: Contixo Pages: 12
Contixo F24 Instruction Manual preview
F24
Brand: Contixo Pages: 34
Contixo F31 Instruction Manual preview
F31
Brand: Contixo Pages: 44
Amcrest A4-W Flight Manual preview
A4-W
Brand: Amcrest Pages: 13

Brands by name

Popular brands

Load more brands