manualshive.com logo in svg

senseFly EBEE RTK, Extended User Manual, Page: 31 / 190

Share
Download
senseFly EBEE RTK Extended User Manual Download Page 31

Setting up RTK

2

Setting up RTK

2.1 Base station compatibility

With built-in support for the standard RTCM RTK data transmission protocols, the

eBee RTK

with

eMotion

can be expected to receive and process corrections from

a wide range of base stations. senseFly has tested a series of RTCM-compliant
base stations from leading brands, checked for non-standard features that might
cause incompatibility, and has thus validated them for use with the

eBee RTK

and

eMotion

.

Some base station manufacturers also make available proprietary data transmis-
sion protocols, and senseFly has used these to develop additional base-

eMotion

automation features for some of these bases.

Please refer to the following Knowledge Base article for a list of base stations that
senseFly has validated, and which base-

eMotion

automation features you should

expect:

https://sensefly.zendesk.com/entries/105423496-Is-my-Base-Station-Compatible-
with-the-eBee-RTK-and-eMotion-

Note:

This list will change as senseFly enhances

eMotion

, so please

refer to this list regularly, especially if purchasing a base station, or if
considering using one with your

eBee RTK

for the first time.

2.2

Setting up your GNSS/RTK base station

To enable high-precision navigation and geo-tagging, connect

eMotion

to an RTK-

capable base station (not provided in the

eBee RTK

package). Corrections will

be sent through the ground modem, and precise geo-tags will be automatically
stored alongside your photos in the automatically generated flight logs.

You can set up several base stations in

eMotion

. Once in the field you can then

quickly change base station using the Choose RTK Source menu on the

eMotion

toolbar.

31

Summary of Contents for EBEE RTK































































































































































































Reviews:

No comments