SenseAir tSENSE VAV No Disp User Manual Download Page 11

 

 

 

 

 

Document 
UMA 192 

Rev 

Page 
11 (12)

 

 

Error codes and action plans 

 

Bit # 

Error code 

Error description 

Suggested action 

CO

2

 sensor 

Com. error 

No ability to communicate 
with CO2 sensor module. 

Try to restart sensor by power 
OFF/ON.  
Contact local distributor.  

CO

2

 sensor 

CO

2

 measure error 

 

CO

2

 measurement error. 

Try Background calibration (see fig. 4 
and 5). 
Contact local distributor. 

See Note 1!  

T sensor 
T measure error 

Temp measurement error. 

 
 
 
 
 
Try to restart sensor by power 
OFF/ON.  

 
 
 
 

Contact local distributor.  

RH/T sensor 
com error 

No ability to communicate 
with RH/T sensor module. 

RH/T sensor 
RH measure error 

RH measurement error. 

RH/T sensor 
T measure error 

Temp measurement error, 
sensor will use CO

2

 sensor 

temperature if RH/T 
Temperature is unavailable. 
S_Temp will be set to 
NTC_Temp. 

 

 

 

 

 

 

Output config. error  Error in output configuration. 

Output is still updated,

 

i.e. can be 0-10V  

Check connections and loads of 
outputs.  
Check detailed settings and 
configuration with UIP software version 
5 or later. 
 
Contact local distributor.  

Table 2:  Error codes and action plans. 

 

NOTE! 

Occurs  if  probe  is  out  of  range,  at  very  high  CO2  values.  Error  code  resets  automatically  when 
measured values returns to normal. May also indicate need of zero point calibration. If CO2

 

values are 

normal and error code remains, the sensor can be defect or the connections to it are broken

 

If  several  errors  are  detected  at  the  same  time,  different  error  code  numbers  will  be  added  together 
into one single error code! 
Sensor accuracy is defined at continuous operation (at least three (3) weeks after installation).  

 

Maintenance 

tSENSE VAV No Disp

 

is maintenance free. Internal self-adjusting calibration function 

takes  care  of  normal  long  term  drift.  To  secure  highest  accuracy,  a  time  interval  of 
five years is recommended between CO

2

 calibrations, unless some special situations 

have occurred. 
 
 
Software can be downloaded free at 

www.senseair.com

.  

USB-cable and zero calibration kit can be ordered from SenseAir. 

 

Check can be done on site without interfering with ventilation system. 

 

 

 

Summary of Contents for tSENSE VAV No Disp













Reviews: