Architects Specifications
SI1015-12500 Dual
The infrared system shall be modular and provide coverage for up to 12500 square feet in dual channel mode.
The SI1015 modulator must utilize the higher sub-carrier frequencies of 2.3 and 2.8 MHz for single, two channel or stereo operation with an AF fre-
quency response of 50-15,000 Hz. It must be rack-mountable and have two monitoring diodes for the technician. It must accept line level audio input
via XLR connector. It must be easy to install using barrier strip with RF and DC outputs for connecting to emitters; and, alternatively, BNC connectors for
connecting the RF signal only. It must have AF level controls with LED’s indicating peak volumes.
The power supply NT1015-120 shall provide power for one SI1015 emitter and shall have an input voltage of 100-240 V (1.3 A), an output voltage of
approx. 29 V and an output current of 1.7 A.
The GA 1031-CC rack adapter is capable of mounting an individual SI 1015 modulator to a 19" rack.
The SI1015, SZI1015 and SZI1029 shall be wall or ceiling mountable via a mounting clamp with 5/8" external male thread, and the mounting plate shall
have a diameter of 1 5/8".
The stethophone shall be a two channel IR receiver with the following: wideband FM, stereo modulation, 2.3 and 2.8 MHz carrier frequencies, 18-18,000
Hz AF frequency response, greater than 1% THD, typ. 65 dB Signal-to-noise ratio, approx. 110 dB max. SPL, approx. 5 hours operating time, and a weight
of approx. 1.58 oz. (including battery pack). The stethophone shall be a Sennheiser HDI302. The receivers shall contain a rechargeable Nickel Metal
Hydride battery, which can easily be recharged with the L151-10 charging unit for up to ten rechargeable batteries. The NT2013-120 power supply is
capable of powering two to five of the L151-10 charging units.
The SZI1029 shall be an infrared high power radiator with RF input for wide and narrow-band signals. Carrier frequency band extends to 6 MHz RF input
(50 mV to 3V) via BNC socket, RF output via BNC socket. The unit shall offer excellent reliability due to 12 independent diode groups with malfunction
indicator. The unit shall offer a 90-280 V AC power supply and weigh approx. 4 lbs. The unit shall be a Sennheiser SZI1029.
The SZA1060 shall weigh 1.0 oz and be a 50 ohm terminating resistor for the last emitter in a daisy chain.
Limited Product Warranty/Service
Sennheiser Electronic Corporation extends the following limited product warranty for Sennheiser products:
The warranty period for all covered Sennheiser products is two years from the date of purchase. Not covered by this warranty are accessories and other consumables;
for example, items of wear and tear, such as cables. During the warranty period, Sennheiser Electronic Corporation warrants that the Sennheiser equipment will be
free from defects in materials and workmanship used in making the product. Abnormal conditions, deliberate abuse and damage due to accidents, operator’s error, or
unauthorized service attempts are excluded from any warranty claims.
Under this warranty, Sennheiser Electronic Corporation will repair, or at its option, replace free of charge the covered defective Sennheiser product, provided it is returned
(postage paid, with proof of purchase from the original seller) to a Sennheiser Service Facility. Products should be returned in their original package, or otherwise suitably
protected to avoid shipping damage. Either product registration or a valid, dated proof of purchase is accepted to establish the warranty period. The Sennheiser Service
Department will be the sole authority to determine the validity of all warranty issues.
This Limited Product Warranty is Sennheiser Electronic Corporation’s only warranty, and the customer’s only remedy concerning Sennheiser products. All other rep-
resentations and warranties, express or implied, written or oral, including, but not limited to, any warranties of merchantability, fitness for a particular purpose, or
non-infringement, are expressly excluded. As a result, except as set forth in the previous paragraphs, the product is sold “as-is” and the customer is assuming the
entire risk as to the product’s suitability for his needs, its quality and its performance.
In no event will Sennheiser Electronic Corporation be liable for direct, indirect, special, incidental or consequential damages resulting from any defect in the product or
from its use, even if advised of the possibility of such damages.
Sennheiser Electronic Corporation • 1 Enterprise Drive • Old Lyme, CT 06371
SI1015-12500 Dual System Package
CBinder - Information Systems.indd 35
11/11/08 11:50:02 AM
