2
EXTERNAL DIMEN IONS
：
S
3
9.87"
[250.6]
9.87"
[250.6]
9.53"
( L
)
[242]
( L
)
9.53"
[242]
8.78"
( L
)
[223]
4.72"
7.30"
[120]
[185.3]
8.78"
( L
)
[223]
7.20"
3
.1
5
"
[183]
[8
0
]
3
.1
5
"
[8
0
]
7.20"
[183]
7.56"
5
.9
1
"
[192]
[1
5
0
]
7.56"
5
.9
1
"
[192]
[1
5
0
]
TA-130-100 (L=1000 mm)
TA-130-150 (L=1500 mm)
TA-130-100 / TA-130-150
TA-120-100 (L=1000 mm)
TA-120-150 (L=1500 mm)
TA-120-100 / TA-120-150
TA-130-200 (L=2000 mm)
TA-130-250 (L=2500 mm)
TA-130-300 (L=3000 mm)
TA-130-200 / TA-130-250
TA-130-300
TA-120-200 / TA-120-250
TA-120-300
TA-120-200 (L=2000 mm)
TA-120-250 (L=2500 mm)
TA-120-300 (L=3000 mm)
No:A064B02-00
Unit :
[
inch mm]
7.87"
8.87"
[200]
[225.3]
b
.
anchor bolts
a
.
sleeve anchors
NOTE
：
1. This unit is designed to detect intruder and activate alarm control panel. Being only a part of complete system,
we cannot assume responsibility for theft or damages, should it occur.
2. Specifications and design are subjected to change without prior notice.
3. No take apart the product improperly, which possibly cause the damage.
6. Wire and fix side brackets to the floor using:
a.Sleeve Anchors :
Ø1/2″(12.7 mm)
fix optional side brackets and tighten sleeve anchors fully.
b.Anchor Bolts : Slide anchor bolts and M10 hex nuts along the floor base unit, embedding the floor base unit into concrete.
Special attention is required when anchoring to uneven surface, be sure a level is used. Few days later,
set side brackets, slide M10 washer/hex nut and tighten fully.
【
Be sure a level is used
】
Making mark and drilling
where tower designated to mount into concrete,
drilling and
marking
sleeve anchors
(3
/
8"x3")
floor base
short side bracket Mark
“ 2” hole (183x80mm)
long side bracket using Mark
“ 1” hole (192x150mm)
hex nuts
(M10)
anchor bolts
use a Level
washers
(M10)
hex nuts
(M10)
7. You can attach and align the beam units to the back plates. Do not fit the original beam covers to the beam units.
8
.
Mount the polycarbonate profile, inserting and sliding it along the Alum-Extrusion.
9
.
Place the nuts in the top cover and insert the hexscrew, screwing them slightly.
Put the top cover on the alum-extrusion, and tighten bolts fully.
Do not fit the
original beam
covers to the
beam units.
Web Site : http://www.sengate.com
E-Mail : service @ sengate.com
Designing / Manufacturing
Taiwan Security Net Co., Ltd.
Designing / Manufacturing
Taiwan Security Net Co., Ltd.
No.4-46,Feng-Jen Road, Renwu, Kaohsiung, 81459, Taiwan
TEL 886-7-3721111 FAX 886-7-3728650
:
:
