ENGLISH - 8/8
MI004542-E
Technical support
Product Information
CONTACTS
Code
Description
Z-PC-DINAL2-52.5
CEI EN 60715 rail connections system with screw terminals. Pitch=52.5 mm
CS-DB9M-MEF-PH
Communication Cable RS232/485 1.5 mt.
CE-RJ45-RJ45-R
Ethernet cable 1.5 mt. (straight)
MSD
Micro SD Card
ORDER CODES
Female 4 pin
connector
1 2
4
3
3 4
2
1
The 4 way for RS232 or RS485 serial
connection cable can be
bought by ordering Seneca
code
:
CS-DB9M-MEF-PH
.
CABLE RS232/ RS485
PIN
RS232
RS485
The cable
length
must be less
than
3 meters.
1
CTS
2
TX
B
3
RX
A
4
GND
GND
RS232/RS485 CABLE
SIM Card
Contatti
metallici
della micro
SD card
SLOT FOR MICRO SD CARD
Z-PASS2 has a slot for micro SD card placed on the
side of the case.
Before pushing the micro SD (or micro SHDC) in this slot,
please be sure that the SD card golden contacts are
facing towards left (as in the picture on side).
SD card any class Max. 32 GB.
The slot is push-push type.
SLOT FOR MINI SIM CARD
Z-PASS2 has a slot for micro SIM card placed on the
side of the case.
Before pushing the mini SIM in this slot, please be sure
that the SIM card golden contacts are facing towards right
(as in the picture on side).
OTHER Z-PASS2 PORTS
ENGLISH - 7/8
MI004542-E
Ethernet 1 RJ45
Ethernet 2 RJ45
USB #1 HOST
3
2 1
21+Vext
20 DIDO2
19 DIDO1
24 GND
23 DO
22 VPN
Load
Load
Load
0V
Max 24V
Load
Tens. Vout+ 12V
20mA
21+Vext
20 DIDO2
19 DIDO1
18 DI
17 RCD
16 +12V
18 DI
17 RCD
16 +12V
0V
Max 24V
21+Vext
20 DIDO2
19 DIDO1
24 GND
23 DO
22 VPN
ELECTRICAL CONNECTIONS FOR DIGITAL INPUTS (RCD, DI, DIDO1 and DIDO2)
The device has :
- 1 Digital input (RCD) reserved for disable
the remote connection
- 1 Digital input (DI).
- 2 channels software onfigurables so as
digital input or digital output (DIDO1 and
DIDO2).
- 1 Digital output reserved to indicate that
VPN is active.
- 1 Digital output (DO).
For configuration and more information
please refer to the USER MANUAL.
ELECTRICAL CONNECTIONS FOR DIGITAL OUTPUTS (VPN, DO, DIDO1 and DIDO2)
ELECTRICAL CONNECTIONS AND Z-PASS2 PORTS
USB #1 HOST PORT
Z-PASS2 has an USB HOST type A connector, here
you can connect a USB memory stick for firmware upgrading.
100mA Max. available current.
ETHERNET RJ45 PORTS (ON FRONTAL PANEL)
Z-PASS2 has two Ethernet ports with RJ45
connectors on the front panel.
SWITCH
The two ports are internally connected in
mode r
d
mode
o separate in LAN / WAN
.
The two ports have the same MAC Address.
RS232 OR RS485 COM1 PORT(4 PINS)
Z-PASS2 has serial RS232 or RS485 COM1
port on the removable 4 pin contacts connector.
The cable length for the RS232 interface must be
less than 3 meters.
ENGLISH - 6/8
MI004542-E
RS 485 (COM4)
6 5 4
B (-) GND
A (+)
B (-) GND
A (+)
3 2 1
RS 485 (COM2)
Power Supply
19 – 28V
50 – 60 Hz
19 – 40V
6W
14
13
15
N.C.
POWER SUPPLY
151413
AC / -
AC / +
POWER SUPPLY
In order to satisfy the electromagnetic compliance requirements:
- Use shielded cables for signals transmission.
- Connect the shield to a preferential ground for devices.
- Space the shielded cables from power cables installations.
(transformers, inverters, motors, induction ovens, etc...).
In addition to the IDC10 connector, power supply can
also be supplied by terminals 14 and 15.
NOTA: A minimum 1A safety fuse, delayed, must be
installed in the power supply line near the device.
RS485 COM 2 AND RS485 COM 4 PORTS
Z-PASS2 module has two serial communication
RS485 ports: COM2 and COM4.
COM2 port can be connected through
1-2-3 screw terminals or by rear IDC10 connector.
ELECTRICAL CONNECTIONS
B
A
Pic. 3
RS485
A
RS485
B
RS485
GND
IDC10
Power supply
AC-
Power supply
AC+
Pic. 4
Please pay atention to the right installation side of the rear IDC10 connector into the Z-PC-
DINAL2-52.5 bus.
In the figure below you can see the meaning of the various pins of the rear IDC10 connector if you
want to provide the signals directly through this connector. The pictures Pic.3 and Pic.4 show, how
to connect powersupply and RS485 COM2 port to the rear IDC10 connector.
USE OF Z-PC-DINAL ACCESSORY
ENGLISH - 5/8
MI004542-E
Pic. 1
Z-PASS2
S
SENECA
STAT
MAIN
ANT
DIV
ANT
PWR
LAN/
WAN
SWITCH
VPN
SERV
RUN
COM1
USB #1
1 2 3
4 5 6
RX1
TX1
RX2
TX2
RX4
TX4
13 14 15
3G PWR
WAN / ETH2
LAN / ETH1
Pic. 2
USB #1
1 2 3
13 14 15
Z-PASS2
S
SENECA
STAT
MAIN
ANT
DIV
ANT
PWR
LAN/
WAN
SWITCH
VPN
SERV
RUN
COM1
4 5 6
RX1
TX1
RX2
TX2
RX4
TX4
3G PWR
WAN / ETH2
LAN / ETH1
Insertion on the IEC EN 60715 DIN rail:
1) Move the two hooks on the back of the module
outwards as illustrated in Pic.2.
2) Insert the module rear IDC10 connector into a free
slot of DIN rail BUS accessory as you can see in Pic.1.
ATTENTION: the insertion is one way only because the
connectors are polarized.
3) To secure the module to the IEC EN 60715 DIN rail,
tighten the two hooks on the side of the IDC10 rear
connector as shown in Pic.1.
Removal from IEC EN 60715 DIN rail:
As shown in Pic.2:
1) Move outwards the two hooks on the side of the
module, with the help of a screwdriver.
2) Extract the module from the IEC EN 60715 DIN rail.
INSTALLATION AND REMOVAL FROM IEC EN 60715 DIN RAIL
Module 2
Module 3
Module 1
Module 5
Module 4
DL
Terminator
Terminator
Bus Length
DL: Derivation Length
Scheme 1
1) Install the modules on the DIN rail (max 120).
2) Connect the remote modules using cables of proper length (see Scheme 1).
On the table the following data about the cables length are provided:
-Bus Length: Modbus network maximum length as a function of the Baud rate.
It is the length of the cables which connect the two bus terminators modules (see Scheme 1).
-Derivation Length (DL): maximum length of a drop line (see Scheme 1).
MODBUS Scheme 1
Bus length
DL
Baudrate
1200 m
2 m
115 kbps
In order to obtain maximum performances it’s
recommended to use a specific shielded cable.
MODBUS CONNECTION STANDARDS
In order to ensure optimum performance and the best device’s operating life, the module(s) must be
provided with adequate ventilation without raceways or other objects that can obstruct the ventilation
slots. Never install the modules near heat sources.
We recommend installation in the lower part of the control panel.
INSTALLATION RULES
A-GPS-SMA
GPS antenna with magnetic and adhesive base. Cable L=3 mt.
All manuals and user guides at all-guides.com
