background image

ENGLISH

- 4/8

MI004950-E

t

POWER SUPPLY

Voltage
Power Absorbed

10 – 40 V

o 19 – 28 V

C

A

a

50    60 Hz

Max: 3,5 W

INPUTS

Input type
Number of Channels
Transition Level
Maximun Frequency
Current consumption
Voltage for input power
supply

Reed, Contact, Proximity PNP, NPN.
5 configurable to PNP or NPN
OFF < 6 V, On > 9 V (max 24 V

)

C

5 Khz
3,5 mA @ 10 V

; 10 mA @ 24 V

C

C

16 V

10%

±

OUTPUTS

Outputs
Number of Channels
Operate/release time delay

SPST relay outputs with common contacts, capacity 2 A

250 Vac.

AC1

2
5/2 ms

TECHNICAL SPECIFICATIONS

PRELIMINARY WARNINGS

Before performing any operation is mandatory to read the full contents of this
manual.

The module may only be used by qualified and skilled technicians in the field of

electric installation. Specific documentation is available for download at website:
www.seneca.it/products/z-8ntc.

Only the Manufacturer is authorized to repair the module or to replace damaged parts.
The product is susceptible to electrostatic discharge, take appropriate countermeasures
during any operation.

No warranty is granted in connection with faults resulting from improper use, from
modifications or repairs carried out by Manufacturer-unauthorized personnel on the
device, or if the content of this user Manual is not followed.

It is forbidden to place anything that could obstruct the ventilation slits.

.

It is forbidden to install the module near heat sources

Severe operating conditions: -Powersupply > 30 V , Powersupply > 26 V

and

C

A

away from the

the module power the input sensor

.

Separate the module at least 5 mm

other devices installed side by side if the module operate with:
- The operating temperature > 40°C and one of the s

exists.

evere operating condition

- The operating temperature > 35°C and two of the s

exist.

evere operating conditions

Disposal of electrical & electronic equipment (applicable throughout the EU and other
countries with separate collection programs).

found on this product or on its

The symbol

packaging indicates that this product it must be handed over to an authorised collection point

,

for

the recycling of electrical and electronic

equipments.

Summary of Contents for Z-5DI-2DO









Reviews: