- 5 -
07/2020
Copyright © 2020, Fast ČR, a.s.
EN
Vacuum Cleaner
User's manual
A1
Cord winding button
A2
Full dust bag indicator
A3
Vacuum hose connection hole
A4
Clip for locking and releasing the
lid
A5
Button for opening the accessory
compartment
A6
B/- serve to control the
power of the motor.
A7
START/STOP button
A8
Rubber-coated wheel
A9
Handle
A10
Sliding flap for air suction
A11
Telescopic tube
A12
Clip for the telescopic tube
A13
Floor nozzle
A14
Flap position for vacuuming
carpets
A15
Flap position for vacuuming hard
(smooth) floors
A16
Hose
A17
Accessory holder (depending on
the model)
A18
Stopper for the horizontal and
vertical parking position
A19
Clip
A20
Hose end
A21
Horizontal parking position
A22
Power cord
A23
Carry handle
A24
Front travel wheel with swivel
mechanism
A25
Vertical parking position
A26
Telescopic slot nozzle for vacuuming
in hard to reach places (e.g. windows,
corners, book shelves, areas between
mattresses, upholstery, etc.)
A27
Upholstery nozzle with an
additional brush
A28
Dust bag collar
A29
Dust bag
A30
Dust bag holder
A31
Inflow micro-filter
A32
Grill of the inflow micro-filter
A33
Outflow micro-filter
A34
Outflow HEPA filter
A35
Grill of the outflow micro-filter
and HEPA filter
ASSEMBLY
Inserting the hose into the air suction hole on the vacuum cleaner:
Press both the safety buttons on the end of the hose
A20
end and insert the hose end
A20
into the air suction opening
A3
on the vacuum cleaner until you hear a “click”. The
hose
A16
is now secured in the correct position.
Attach the holder to the telescopic tube:
Make sure to place the holder with the hose on the wider part of the telescopic tube
A11
.
Attach the floor nozzle to the telescopic tube:
Make sure the floor nozzle
A13
is attached the narrower part of the telescopic tube
A11
.
Adjust the length of the telescopic tube:
Adjust the length of the telescopic tube
A11
as required – disengage and hold the clip
A12
on the tube
A11
in the direction shown by the arrow and adjust the length of the
tube
A11
as required. Then release the clip
A12
and slide out the tube
A11
slightly
forward until you hear a “click”. The telescopic tube
A11
is now securely fixed in position.
USING THE VACUUM CLEANER
Connecting your vacuum cleaner to the power grid
Wind out the required length of the power cord
A22
by pulling on the power plug. Insert
the power plug into a power socket.
Caution:
Yellow marking on the power cord warns that the power cord
is close to its end. Do not pull the cord further than the red
marking.
Adjusting the floor inlet nozzle according to the floor surface.
You may set the inlet nozzle
A13
according to the floor surface by adjusting the inlet flap:
• If you want to vacuum carpets, close the bristles of the inlet inside the inlet nozzle,
by turning the flap accordingly.
• If you want to vacuum hard and smooth surfaces, extend the bristles out of the
nozzle, by turning the flap accordingly.
Turning your vacuum cleaner on and off
To switch your vacuum cleaner on, press the START/STOP button
A7
. To turn off the
vacuum cleaner, press the button
A7
again.
Adjusting the suction power
Suction can be controlled using b/-
A6
. The power of the vacuum cleaner is
increased using the + button, decreased using the - button. In a smaller range, you may
regulate suction power using the mechanically sliding flap
A10
on the hose handle
A9
.
Tips
• Use the maximum suction strength when vacuuming carpets
or floors with a hard surface. Use the reduced strength when
vacuuming upholstery, window curtains, etc.
•
If the hose holder
A9
becomes blocked when vacuuming,
disconnect it from the telescopic tube
A11
and also disconnect
the hose
A16
from the vacuum cleaner body. Then place the
holder inside the suction hole on the vacuum cleaner body and
vacuum out the stuck dirt.
Temporary interruption of the vacuuming process
If you wish to interrupt vacuuming for a while, you can use the horizontal
A21
or vertical
A25
parking position on the vacuum cleaner, into which you insert the stopper
A18
on the floor nozzle
A13
.
Attention:
Do not move the vacuum cleaner from place to place if the hose
A16
is in the parked position! The stopper
A18
on the floor
nozzle
A13
could brake off.
Ending the vacuuming process
When you finish vacuuming, switch the vacuum cleaner off by pressing the START/STOP
button
A7
and then disconnect the power cord plug from the socket.
To wind the power cord
A22
back into the vacuum cleaner, press and hold the winding
button
A1
with one hand and guide the power cord
A22
with the other.
Tip:
If the winding process stops and part of the power cord
A22
is still outside,
release the winding button
A1
and pull the cable out again by about
50 cm and then press and hold the winding button
A1
again and repeat
the winding process.
Carrying the vacuum cleaner
It is possible to hold and carry the vacuum by the handle
A23
.
CLEANING AND MAINTENANCE
Caution:
Before cleaning, disconnect this appliance from the power
source.
Changing the dust bag
When the full dust bag indicator
A2
lights up, it is necessary to replace the dust bag
A29
.
If you do not remove the dust bag
A29
, the suction power will be reduced.
1) Open the vacuum cleaner filter area by pressing the lid clip
A4
while pulling it upwards
at the same time.
2) By pulling on the collar
A28
of the dust bag in the direction of the arrow, remove it
from the plastic holder
A30
and insert a new bag.
3) Close the lid of the vacuum cleaner, until you hear a click.
Replacing and cleaning the inflow micro-filter and outflow HEPA filter and micro-filter
1) Open the vacuum cleaner filter area by pressing the lid clip
A4
while pulling it upwards
at the same time.
2) By pulling on the collar
A28
of the dust bag in the direction of the arrow, remove it
from the plastic holder
A30
to make room for the removal of the filter.
3) Pull the inflow micro-filter grill
A32
towards yourself and take out the micro-filter
A31
.
4) Simultaneously press both PUSH buttons at the rear of the vacuum cleaner. This will
tilt out the rear grill
A35
of the outflow micro-filter and HEPA filter. Put the grill
A35
aside and take out both filters.
5) If the micro-filters are
A31
,
A33
slightly soiled, it is possible to wash them under
running lukewarm water. If the HEPA filter
A34
is slightly soiled, it is possible to
quickly wash it under a weak current of running lukewarm water. This will remove
dust and dirt found on its surface. In the event of heavy soiling, replace the filters
with new ones.
6) Allow washed filters
A31
,
A33
to dry naturally. Do not dry them over heaters or using
hair dryers. Then put the inflow micro-filter
A31
, outflow HEPA filter
A34
, micro-filter
A33
and the grills back in their place.
7) Return the dust bag
A29
.
8) Close the lid of the vacuum cleaner, until you hear a click.
Attention:
Never insert the filters back into the vacuum cleaner if they are
wet or damp! Always wait until they are thoroughly dry.
Cleaning your vacuum cleaner.
To clean the outside parts of the appliance, use a fine cloth dipped in lukewarm water.
Do not use aggressive cleaning agents, paint thinners or solvents. Using these solutions
could damage the surface of the appliance.
