- 5 -
09/2020
Copyright © 2020, Fast ČR, a.s.
EN
Bagless vacuum cleaner
User's manual
DESCRIPTION OF THE VACUUM CLEANER
A1
Cord winding button
A2
On/Off button
A3
Suction power control knob
A4
PUSH button (serves to release the
dust container)
A5
Rubber coated wheels
A6
Dust container lid
A7
Dust container
A8
Hose connection hole
A9
Handle
A10
Sliding flap for air suction
A11
Telescopic tube
A12
Telescopic tube position lock
A13
Combination floor nozzle
A14
Flap position for vacuuming carpets
A15
Flap position for vacuuming hard
(smooth) floors
A16
Hose
A17
Accessory holder
A18
Stopper for the horizontal and
vertical parking position
A19
Clip
A20
Hose end
A21
Front travel wheel
A22
Vertical parking position
A23
Power cord
A24
Inflow filter
A25
Foam pre-filter
A26
Horizontal parking position
A27
Outflow filter
A28
Outflow filter protective grille
A29
Long flexible crevice nozzle
A30
Crevice nozzle
A31
Upholstery nozzle
A32
Brush attachment (easy to attach
to the upholstery nozzle for gentle
vacuuming of fine upholstered
surfaces)
A33
Hard floor nozzle
A34
Mini turbo brush
ASSEMBLY
Inserting the hose into the air suction hole on the vacuum cleaner.
■
Press both the clips on the end of the hose
A20
and insert it into the air suction hole
A8
on the vacuum cleaner until you hear a "click". The hose
A16
is now secured in
the correct position.
Attach the holder to the telescopic tube:
■
Make sure to place the holder with the hose on the wider part of the telescopic
tube
A11
.
Attach the floor nozzle to the telescopic tube:
■
Make sure that the floor nozzle
A13
is attached to the narrower part of the
telescopic tube
A11
.
Adjust the length of the telescopic tube:
■
Adjust the length of the telescopic tube
A11
as required – disengage and hold the
clip
A19
on the tube in the direction shown by the arrow and adjust the length
of the tube
A11
as required. Then release the clip
A19
and slide out the tube
A11
slightly forward until you hear a "click". The telescopic tube
A11
is now securely
locked in position.
USING THE VACUUM CLEANER
Connecting the vacuum cleaner to the power grid
■
Wind out the required length of the power cord by pulling on the power plug. Insert
the power plug into a power socket.
Attention:
The yellow marking on the power cord warns you that the power
cord is close to its end. Do not pull the cord farther than the red
marking.
Adjusting the floor inlet nozzle according to the floor surface.
■
You may set the inlet nozzle according to the floor surface by adjusting the inlet flap:
- If you want to vacuum carpets, move the flap to retract the bristles.
- If you want to vacuum hard and smooth surfaces, move the flap to extend the
bristles.
Turning your vacuum cleaner on and off
■
To turn on the vacuum cleaner, press the On/Off button
A2
. To turn off the vacuum
cleaner, press the button
A2
again.
Adjusting the suction power
■
Suction can be controlled using the control knob
A3
. Turning clockwise (towards
MAX) increases the power of the vacuum cleaner, turning anticlockwise (towards
MIN) reduces the power. In a smaller range, you may regulate suction power using
the mechanically sliding flap
A10
on the hose handle.
TIPS
■
Use the maximum suction power when vacuuming carpets or floors with a hard
surface. Use the reduced strength when vacuuming upholstery, window curtains,
etc.
■
If the hose holder becomes blocked when vacuuming, disconnect it from the
telescopic tube and also disconnect the hose from the vacuum cleaner body.
Then place the holder inside the suction hole on the vacuum cleaner body and
vacuum the stuck dirt out.
Temporary interruption of the vacuuming process
■
If you wish to interrupt vacuuming for a while, you can use the horizontal
A26
or
vertical
A22
parking position on the vacuum cleaner, into which you insert the
stopper
A18
on the floor nozzle.
Attention:
Do not move the vacuum cleaner from place to place if the hose
is in the parked position! The stopper on the floor nozzle could
brake off.
Ending the vacuuming process
■
When you finish vacuuming, switch the vacuum cleaner off by pressing the On/Off
button
A2
and then disconnect the power cord plug from the power socket.
■
To wind the power cord back into the vacuum cleaner, press and hold the winding
button
A1
with one hand and guide the power cord with the other.
TIP:
■
If the winding process stops and part of the power cord is still outside, release the
winding button
A1
and pull the cable out again by about 50 cm and then press
and hold the winding button
A1
again and repeat the winding process.
USING THE ACCESSORIES
■
The combination floor nozzle
A13
for hard floors ensures perfect and yet gentle
vacuuming of smooth hard surfaces thanks to the brush being from 100 % natural
bristles. It can be used to vacuum floors that are sensitive to scratching such as
wooden or floating floors, marble floors, tiles, linoleum, etc.
■
The long flexible crevice nozzle
A29
serves to vacuum very hard-to-reach places
anywhere in your car.
■
The crevice nozzle
A30
is suitable for vacuuming hard to reach places (e.g. window
frames, libraries, upholstery corners, joints, etc.).
■
The hard floor nozzle
A33
ensures perfect and yet gentle vacuuming of smooth
hard surfaces thanks to the brush being from 100% natural bristles. It can be used
to vacuum floors that are sensitive to scratching such as wooden or floating floors,
marble floors, tiles, linoleum, etc.
■
The mini turbo brush
A34
is the ideal helper for removing animal fur, hair, etc.,
while at the same time being suitable for vacuuming hard-to-reach places. Its use
is not limited to the home, and can be used for vacuuming the car. It quickly and
effectively removes hair, animal fur and other materials from car seats, upholstery,
pillows and other textile surfaces.
TIP:
■
If during vacuuming you use an accessory very often, you may attach it to the
special holder on the telescopic tube.
CLEANING AND MAINTENANCE
Attention:
Before cleaning, disconnect this appliance from the power source.
Emptying the dust container
■
Empty the dust container
A7
as soon as it fills up to the MAX mark; otherwise the
air flow and the suction power will be reduced. Nevertheless, it is recommended to
always empty out the dust container when you have finished vacuuming.
1. Take out the hose
A16
.
2. Press the PUSH
A4
button and pull out the dust container
A7
upwards.
3. Remove the lid of the container
A6
and take out the dust filter. Tip the dust out of it
and rinse it out under lukewarm running water if necessary.
4. Take the dust container
A7
above a waste bin and turn it upside down to shake the
dirt and dust out of it. If it is heavily soiled you may wash the entire container under
running lukewarm water. It is, however, necessary to first remove the inflow filter
A24
and its foam pre-filter
A25
before doing this!
5. Insert the dust filter into the dust container
A7
and put on the lid
A6
.
6. Insert the container
A7
into the vacuum cleaner.
Attention:
Make sure that all parts are completely dry before reinserting
the dust container
A7
and the dust filter back into the vacuum
cleaner.
