Sencor STM 7870GG, Original Manual

Page: 10 / 11

- 10 -
05/2020
Copyright © 2020, Fast ČR, a.s.
USING THE SAUSAGE STUFFER ATTACHMENT
1. Make sure that the food processor is correctly assembled and that the speed
control knob A13 is set to the OFF position. Insert the power plug into a power
socket.
2. Prepare a sausage casing that you will stuff with ground meat and allow it to soak
in lukewarm water for approx. 10 minutes. Place the ground meat mixture on to
the hopper B2 . Take the sausage casing out of the water and skewer or tie up one
end and slide the other end like a sock on to the sausage stuffer attachment
B12
.
3. Use the speed control knob A13 to set the desired speed. We recommend to
initially set the lowest speed and then increase it as required. With one hand hold
the sausage casing on the attachment B12 and use the other hand to push the
ground meat mixture with the pusher
B1
through the feed tube
B3
. If the sausage
casing sticks to the attachment B12 , it is necessary to moisten it with water again.
Attention:
Do not use fingers or other items to push the ground meat in.
Always use the pusher B1 designed for this purpose.
4. To turn off the appliance, set the speed control knob A13 to the OFF position.
5. Clean out the individual parts of the attachment after each use according to the
instructions in chapter Cleaning and maintenance.
ASSEMBLING AND DISASSEMBLING THE KEBAB MAKER
ATTACHMENT
1. Proceed in the same way as when assembling the meat grinder, only with the
difference that instead of the grinding blade
B6
and the grinding plate
B8
,
B9
or
B10 , only parts B13 a B14 are used.
2. Place the moulder
B13
on to the screw shaft
B5
so that the notch in the grinding
chamber B4 fits into the groove in the moulder B13 . Place the kebab moulder
attachment
B13
on to the conical attachment
B14
and complete the entire kebab
maker assembly by screwing the screw ring B7 on to the grinding chamber B4 .
Place the stainless steel hopper
B2
on to the feed tube
B3
.
3. Attach the attachment to the food processor in the same way as described in point
4 in chapter Assembling and disassembling the meat grinder.
4. When disassembling, first remove the hopper B2 . Then press the button A1 and
remove the attachment by turning it clockwise. After removing the attachment,
put the cover A2 back in its place.
5. When disassembling the attachment into its individual parts, proceed in the
reverse sequence.
USING THE KEBAB MAKER ATTACHMENT
1. Make sure that the food processor is correctly assembled and that the speed
control knob A13 is set to the OFF position. Insert the power plug into a power
socket.
2. Place the prepared kebab meat mixture on to the hopper B2 . Use the speed control
knob A13 to set the desired speed. We recommend to initially set the lowest speed
and then increase it as required. Using the pusher B1 , push the mixture through
the feed tube B3 . The result will be a hollow meat tube that is then cut into smaller
pieces. The kebab is a traditional meal from the Middle East made predominantly
from ground meat and whole grain wheat.
Attention:
Do not use fingers or other items to push the ground meat in.
Always use the pusher B1 designed for this purpose.
3. To turn off the appliance, set the speed control knob A13 to the OFF position.
4. Clean out the individual parts of the attachment after each use according to the
instructions in chapter Cleaning and maintenance.
ASSEMBLING AND DISASSEMBLING THE COOKIE MAKER ATTACHMENT
1. Proceed in the same way as when assembling the meat grinder, only with the
difference that instead of the grinding blade
B6
and the grinding plate
B8
,
B9
or
B10 only parts B11 , B15 and B16 are used.
2. Place the separator B11 on to the screw shaft so that the notch in the grinding
chamber B4 fits into the groove in the separator B11 . Insert the cookie maker
holder B16 into the screw ring B7 . Screw the screw ring B7 clockwise on to the
grinding chamber B4 . Complete the assembly by inserting the cookie maker B15
into the holder B16 and attaching the hopper B2 to the feed tube B3 .
3. Attach the attachment to the food processor in the same way as described in point
4 in chapter Assembling and disassembling the meat grinder.
4. When disassembling
, first remove the hopper B2 . Then press the button A1 and
remove the attachment by turning it clockwise. After removing the attachment,
put the cover
A2
back in its place.
5. When disassembling the attachment into its individual parts, proceed in the
reverse sequence.
USING THE COOKIE MAKER ATTACHMENT
1. Place the prepared dough on to the hopper B2 . Slide the cookie maker B15 to the
left or right to set the desired cookie shape.
2. Insert the power plug into a power socket. Set the required speed using the speed
control knob A13 . When starting it for the first time, we recommend that you set
speed 3 and then increase or decrease it as required.
3. Use the pusher B1 to push the dough through the feed tube B3 . The food
processor will push the dough out in the required shape that you set using the
cookie maker B15 . We recommend that you place a tray or your palm underneath
the pushed out dough. Then cut the formed dough into smaller pieces.
Attention:
Do not use fingers or other items to push the dough in. Always
use the pusher
B1
.
4. When you have finished using the food processor, turn it off by setting the speed
control knob A13 to the OFF position.
5. Clean out the attachment after each use according to the instructions in chapter
Cleaning and maintenance.
BLENDING
ASSEMBLING AND DISASSEMBLING THE BLENDER
1. On to the blending jar
C4
, place the outer lid
C2
so that its edges copy the neck of
the jar, and push it down thoroughly along its entire perimeter. Into the hole in the
lid
C2
, place the inner cap
C1
and push it down all the way.
2. Make sure that the food processor is turned off and disconnected from the power
socket. The multi-function head
A8
must be tilted down in the horizontal position
and the whisk, beater or kneading attachments must be removed. Release and
remove the top attachment hub cover
A7
. Place the assembled blending jar on to
the top hub and pulling it gently turn it in the direction of the symbol all the way.
The safety mechanism will prevent the blender from starting unless it is correctly
secured to the multi-function head A8 .
3. To disassemble proceed in the reverse sequence.
4. Prior to starting the appliance, check that the blade assembly C6 is correctly seated
in the cuff C5 . Properly tighten the cuff C5 on to the mixing container C4 .
USING THE BLENDER
1. The blender is intended for preparing meals and drinks such as milkshakes, creamy
soups, sauces, spreads, fresh baby foods, etc. It is not intended for juicing fruit and
vegetables, preparing potato purée, yeast dough or for whipping egg whites.
2. Assemble the blender according to the instructions in chapter Assembling and
disassembling the blender, and put the ingredients (larger pieces need to be cut
up in advance) into the blending jar
C4
.
Note:
The maximum capacity of the blending jar
C4
is 1.5 litres. Never fill it past
the maximum mark. When processing hot liquids or liquids that expand in
volume during the blending process, it is recommended to fill the blending
jar to no more than
⅔
of its maximum capacity.
3. Make sure that the food processor is correctly assembled and that the speed
control knob
A13
is set to the OFF position. Connect the power cord to a power
socket. Set the required speed using the speed control knob A13 . We recommend
to first set a slower speed to allow the ingredients to mix together. Then the speed
may be increased. The pulse level is appropriate when you wish to blend food only
very quickly. To start the pulse level, turn the speed control knob A13 to the PULSE
position and hold it in this position for a moment. As soon as you release the speed
control knob A13 , it will automatically return to the OFF position.
Attention:
Hot liquids up to a temperature of 55 °C may be processed in
the blending jar. The maximum operating time of the blender is
2 minutes. Do not leave the appliance in continuous operation
for longer than indicated above. Then allow it to cool down for
30 minutes.
4. While blending, you may add food or liquids to the blending jar C4 through the
hole in the lid C2 after removing the inner cap C1 . Never open the outer lid C2
during operation. When processing hot liquids, the inner cap C1 must remain
closed.
5. In the event that food is sticking to the blade assembly C6 or the walls of the
blending jar C4 , turn the appliance off by turning the speed control knob A13
to the OFF position and disconnect it from the power socket. Make sure that
the blade assembly C6 has stopped rotating. Carefully remove the assembled
blending jar from the multi-function head A8 by turning it in the direction of the
symbol . Take off the lid and using a plastic spatula, clean the blade assembly
C6
and the inside of the blending jar C4 . Put the lid back on and reattach the blender
assembly to the multi-function head A8 . Plug the power cord into a power socket
and continue blending.
6. After you have finished using the appliance, set the speed control knob A13 to the
OFF position and disconnect the power cord from the power socket. Check that
the blade assembly C6 has stopped rotating and carefully take the blending jar
assembly off the multi-function head A8 . Put the cover A7 back in its place and use
a soft plastic spatula to remove food from the blending jar C4 .