- 6 -
05/2020
Copyright © 2020, Fast ČR, a.s.
EN
Electric Sonic Toothbrush
User's manual
■
Prior to using this appliance, please read the user’s manual thoroughly, even
in cases, when one has already familiarised themselves with previous use of
similar types of appliances. Only use the appliance in the manner described
in this user’s manual. Keep this user’s manual in a safe place where it can be
easily retrieved for future use.
■
We recommend saving the original cardboard box, packaging material, purchase
receipt and responsibility statement of the vendor and warranty card for at
least the duration of the legal liability for unsatisfactory performance or quality.
In the event of transportation, we recommend that you pack the appliance in
the original box from the manufacturer.
DESCRIPTION OF THE TOOTHBRUSH AND ITS ACCESSORIES
A1
Toothbrush head*
A2
Ergonomically-shaped anti-slip
handle
A3
Button for turning the toothbrush
on and off and selecting the
brushing mode
Depending on the selected
mode, the speed is set to 31 000,
41 000 or 48 000 vibrations per
second.
A4
Brushing mode setting LED
indicators
A5
Operation or charging of the
toothbrush LED indicator
A6
Charging stand
A7
Power cord
A8
Travel charger case
A9
USB cable
*Note:
2 toothbrush heads are included.
DESCRIPTION OF THE TRAVEL CASE
B1
Lid
B2
Toothbrush head storage space
One or two toothbrush heads can
be stored in this space.
B3
Toothbrush handle storage space
B4
Charging unit
B5
USB micro port
ATTACHING AND REMOVING THE TOOTHBRUSH HEAD
■
Make sure that the toothbrush is turned off before attaching or removing
a toothbrush head
A1
.
■
Attach the toothbrush head
A1
by sliding it on to the handle
A2
from above.
■
Take off the toothbrush head
A1
by pulling it away from the handle
A2
.
CHARGING THE TOOTHBRUSH
■
This toothbrush has a built-in Li-Ion battery that enables cordless operation.
■
Make sure that the toothbrush is turned off before charging it.
1. IN THE CHARGING STAND
■
Locate the charging stand
A6
on an even and stable surface and plug the power
cord
A7
into a power socket (100–240 V).
■
Put the toothbrush on to the stand
A6
from above, see figure C. When charging,
LED indicator
A5
is lit red and LED indicators
A4
gradually light up and turn
off. When the battery is fully charged, the LED indicator
A5
will be lit blue and
LED indicators
A4
will turn off. After charging, disconnect the charging stand
A6
from the power socket.
Note:
Allow the toothbrush to charge for at least 15 hours before first use and
after not using it for a long time.
If you are charging the toothbrush for the first time or if you have not
used it for a long time, it may take up to 10 minutes before the charging
indicator
A5
lights up.
■
A fully charged toothbrush will provide approximately 180 hours of operation.
If you brush your teeth twice a day for 2 minutes, the toothbrush will last for
45 days without needing to be recharged.
2. IN THE TRAVEL CHARGER CASE
■
Place the travel case
A8
on a dry even surface. Open the lid
B1
and insert the
toothbrush handle
A2
into space
B3
so that the end of the charging unit
B4
slides into the toothbrush handle
A2
. The lid
B1
may be left open or it may
be closed.
■
To supply power to the charger case
A8
from an external USB interface, e.g.
your computer, powerbank, etc., connect the USB micro port
B5
to an external
USB interface using USB cable
A9
.
■
When the travel case
A8
is connected to a charging power source, the charging
process will start.
■
After finishing charging, disconnect the travel case
A8
from the external USB
interface.
HOW TO ACHIEVE THE LONGEST POSSIBLE BATTERY LIFETIME
■
To ensure the longest possible lifetime of the battery, we recommend:
– store, use and charge the battery at room temperature. Excessively high
temperatures may negatively affect its lifetime.
– do not unnecessarily leave the battery fully charged or completely flat for
too long.
– do not keep the battery permanently fully charged.
– do not fully discharge the battery.
USING THE TOOTHBRUSH
■
Make sure that the toothbrush is properly assembled before using it. Wet the
toothbrush bristles with water and apply the toothpaste. Turn on the toothbrush
by pressing button
A3
.
1. CORRECT BRUSHING TECHNIQUE
■
We recommend to start by brushing the right half of the upper dental arch from
the outer side. When brushing, proceed from back to front. Place the toothbrush
bristles on to the teeth at an angle of 45° in line with the gum, see figure D.
Using short slow motions, move the toothbrush to the other teeth. Once the
outer side of the upper right dental arch is brushed, move the toothbrush to
the inner side of the dental arch. Again, proceed from back to front. Adjust the
toothbrush angle to the tooth arrangement. When brushing the inner side of
the front teeth, hold the toothbrush handle
A2
vertical so that the tip of the
toothbrush head
A1
points upwards. Finally, brush the upper tooth surfaces.
■
In the same way, brush the right half of the lower dental arch, the left half of
the lower dental arch and finally also the left half of the upper dental arch.
When brushing the inner side of the front teeth of the lower dental arch, hold
the toothbrush handle
A2
vertical so that the tip of the toothbrush head
A1
points downwards.
2. SETTING UP THE BRUSHING MODE
■
Repeatedly press button
A3
to switch between the modes: CLEAN (standard
brushing), WHITE (whitening), POLISH (polishing), MASSAGE (massaging) and
SENSITIVE (gentle brushing). To change the set mode, it is necessary to press
button
A3
within 5 seconds of turning on the toothbrush or from the last mode
setting change, while LED indicator
A4
is flashing the actual selected mode.
After this time has elapsed, LED indicator
A4
will stop flashing and when button
A3
is pressed the toothbrush will turn off. The last setting is saved to memory.
This means that the next time the toothbrush is started, it will run in the mode
that was set previously.
■
CLEAN mode is intended for standard everyday tooth brushing. WHITE mode
is intended for more intensive tooth brushing (whitening). POLISH mode is
intended for tooth polishing. MASSAGE mode is a combination of tooth brushing
and gum massaging. SENSITIVE mode is intended for brushing sensitive teeth.
3. 4PACER FUNCTION
■
The toothbrush has a timer function that momentarily pauses the toothbrush
every 30 seconds until it turns off automatically, thereby informing the user that
it is time to start brushing the next part of your teeth. This will ensure that all
the dental quadrants are brushed for the same amount of time.
4. AUTOMATIC SHUT-OFF TIMER
■
The automatic shut-off timer automatically turns the toothbrush off after
2 minutes of operation. This is the tooth brushing time recommended by
dentists for the sonic toothbrush.
■
When the toothbrush is turned off, the LED indicators
A4
and
A5
will flash a few
times and then turn off.
■
When you have finished using it, make sure that the toothbrush is turned off
and clean it according to the instructions contained in chapter Cleaning and
maintenance. Then put it back on to the charging stand
A6
or into the case
A8
. Before putting it into the case, it is necessary to remove the head
A1
from
the toothbrush handle
A2
.
CLEANING AND MAINTENANCE
■
For hygiene reasons, regularly clean the toothbrush after every use.
■
Make sure that the toothbrush is turned off before cleaning it.
■
Thoroughly rinse the toothbrush head
A1
under lukewarm running water to
remove any toothpaste or other remains. If whitening pastes are used when
brushing teeth, it is recommended to apply a drop of soap on to the toothbrush
head
A1
and then thoroughly wash it under running lukewarm water. Remove
the toothbrush head
A1
from the handle
A2
at least once per week and clean
it under running water in the location where it is attached to the handle
A2
.
■
Rinse the toothbrush handle
A2
under running lukewarm water and then dry it.
■
In the event that the charging stand
A6
is soiled, wipe it with a clean dampened
cloth and then wipe dry. Ensure that the power plug contacts do not come into
contact with water or moisture.
