02/2017
- 5 -
Copyright © 2017, Fast ČR, a.s.
EN
Food Chopper
User's manual
■
Prior to using this appliance, please read the user’s manual
thoroughly, even in cases where you have previously familiarised
yourself with the operation of similar types of appliances. Only
use the appliance in the manner described in this user’s manual.
Keep this user’s manual in a safe place where it can be easily
retrieved for future reference.
■
We recommend saving the original cardboard box, packaging
material, purchase receipt and responsibility statement of the
vendor or warranty card for at least the duration of the legal
liability for unsatisfactory performance or quality. In the event
of transportation, we recommend that you pack the appliance
in the original box from the manufacturer.
DESCRIPTION OF THE APPLIANCE
A1
Pulse button
for turning the motor unit
on and off
A2
Motor unit
A3
Bowl cover
A4
Blade assembly
A5
1-litre glass bowl
A6
Rubber anti-slip ring
A7
Storage lid
BEFORE FIRST USE
1. Take the appliance and its accessories out of the packaging
materials.
2. Thoroughly wash the cover
A3
, blade assembly
A4
and bowl
A5
in warm water and neutral kitchen detergent. Then rinse with
clean water and allow it to dry naturally or dry it out thoroughly
using a wiping cloth. The glass bowl
A5
can also be washed
in a dishwasher. Other parts are not intended for washing in
a dishwasher..
Attention:
When cleaning the blade assembly
A4
, be very careful not
to injure yourself on its sharp edge.
ASSEMBLING AND DISASSEMBLING THE APPLIANCE
1. Before you start assembling or disassembling the appliance,
check that the motor unit
A2
is turned off and disconnected
from the power socket and that the rotating parts have come to
a complete stop.
2. Place the bowl
A5
into the anti-slip ring
A6
and place it on a dry,
even and stable surface.
3. Seat the blade assembly
A4
on to the central pin at the bottom
of the bowl
A5
and cover the bowl
A5
with the cover
A3
. Push
the cover
A3
down along the entire perimeter so that it is
securely seated on the edge of the bowl
A5
.
4. Place the motor unit
A2
on to the cover
A3
and check that it has
slid in properly. Now the appliance is assembled.
5. To disassemble proceed in the reverse sequence.
OPERATING THE APPLIANCE
1. Assemble the chopper according to the instructions in the
chapter Assembling and disassembling the appliance. Place
the food into the bowl
A5
after seating the blade assembly
A4
on the central pin. Fill the bowl
A5
to a maximum of ¾ of its
volume.
2. Connect the power cord to an electrical power socket and press
the pulse button
A1
to start the chopper. Hold down the button
A1
for several seconds and then release it. When the button
A1
is released, the chopper will stop. If the food inside is not
sufficiently chopped up, run the chopper again for a short time.
Short pulse switching will limit excessive pulverisation of the
food.
Attention:
The maximum continuous operating time of the appliance
is 30 seconds. Then allow it to cool down for 2 minutes.
3. If food sticks to the inside of the bowl
A5
, turn off the chopper
and disconnect it from the power socket. Make sure that the
blade assembly
A4
has stopped rotating. Take off the motor
unit
A2
and the cover
A3
. Clean the inside of the bowl
A5
using
a spatula. Assemble the chopper, plug the power cord into
a power socket and continue processing food.
4. After you finish using it, disconnect the power cord from
the power socket. Make sure that the blade assembly
A4
has
stopped rotating. Take off the motor unit
A2
and the cover
A3
.
First, carefully take the blade assembly
A4
out of the bowl
A5
and only then empty out its contents.
5. Then clean all used parts according to the instructions in
chapter Cleaning and maintenance.
QUICK GUIDE TO PROCESSING INGREDIENTS
■
First, cut up the food into smaller cubes of approximately
2 × 2 cm and only then process with the chopper. With
vegetables like onion, it is sufficient to cut them into quarters.
Ingredients
Maximum
load
Processing
time
Meat
300 g
30 s
Fruit and vegetables
200 g
15 s
Hard and semi-hard cheeses
150 g
10 s
Nuts with shells removed
100 g
15 s
Herbs
50 g
10 s
Note:
The above food processing times are only a reference.
The actual processing time depends on the size of
the ingredients, their amount and the required final
consistency.
CLEANING AND MAINTENANCE
■
Before cleaning it, make sure that the appliance is turned off,
disconnected from the power socket and that the rotating parts
have stopped.
■
Disassemble the appliance into its individual parts. Thoroughly
wash the cover
A3
, blade assembly
A4
and bowl
A5
in warm
water and neutral kitchen detergent. Then rinse with clean
water and allow these parts to dry naturally or dry them out
thoroughly using a wiping cloth. If the anti-slip ring
A6
becomes
soiled, you may wash it in the same way. The glass bowl
A5
can
also be washed in a dishwasher. Other parts are not intended to
for washing in a dishwasher.
Attention:
When cleaning the blade assembly
A4
, be very careful not
to injure yourself on its sharp edge.
