06/2017
- 5 -
Copyright © 2017, Fast ČR, a.s.
EN
Pedestal Fan
User's manual
■
Prior to using this appliance, please read the user’s manual
thoroughly, even in cases, when one has already familiarised
themselves with previous use of similar types of appliances. Only
use the appliance in the manner described in this user’s manual.
Keep this user’s manual in a safe place where it can be easily
retrieved for future use.
■
We recommend saving the original cardboard box, packaging
material, purchase receipt and responsibility statement of the
vendor or warranty card for at least the duration of the legal
liability for unsatisfactory performance or quality. In the event of
transportation, we recommend that you pack the appliance in the
original box from the manufacturer.
DESCRIPTION OF THE APPLIANCE
A1
Horizontal oscillation toggle switch
A2
Motor unit with adjustable vertical tilt angle
A3
Panel with control buttons
0 – off, 1 – low speed, 2 – medium speed, 3 – high speed
A4
Screw for fastening the control panel to the extensible pole
A5
Inner extensible pole
A6
Inner extension lock
A7
Outer pole
A8
Cross base central connecting piece
A9
Cross base feet
A10
Butterfly screw with washer
Serves to fasten the outer pole to the base.
A11
Motor unit shaft
A12
Rear protective grill with fastening clamps and a carry handle
A13
Rear protective grill fastening nut
A14
Fan blades with a diameter of 40 cm
A15
Fan blade fastening nut
A16
Front protective grill
Note:
The accessories include a screw and a nut for joining the
protective grills.
BEFORE FIRST USE
■
Take the appliance and its accessories out of the packaging
materials. Before disposing of the packaging materials, make sure
that no part of the appliance is missing.
ASSEMBLING AND DISASSEMBLING THE APPLIANCE
■
Before assembling or disassembling the appliance, make sure that
it is turned off and disconnected from the power socket.
■
Secure the feet
A9
in the cross base central connecting piece
A8
.
Fit the outer pole
A7
from above into the cross base connecting
piece
A8
and fasten from underneath using the butterfly screw
A10
(see fig. B).
■
Use one hand to firmly hold the outer pole
A7
and the other hand
to release the inner extension lock
A6
by turning the locking
screw anticlockwise. Slide the inner pole
A5
out all the way and
secure it firmly by tightening the locking screw clockwise.
■
Use a cross-head screwdriver to loosen screw
A4
. On to the
inner pole
A5
, slide the control panel
A3
and secure it firmly by
tightening the screw
A4
.
■
Place the base with the attached control panel
A3
on a clean,
even, stable and smooth surface. Place the rear protective grill
A12
against the front side of the motor unit
A2
so that the shaft
A11
passes through the centre of the grill
A12
, so that the tabs
on the front side of the motor unit
A2
fit into the holes in the
central part of the rear grill
A12
and so that the handle is above
the motor unit
A2
. Screw the nut
A13
clockwise to secure the rear
protective grill
A12
to the motor unit
A2
. Before tightening the
nut
A13
, make sure that the rear grill
A12
has not moved and that
the alignment tabs are still in the holes.
■
On to the shaft of the motor unit
A11
put on the fan blades
A14
so that the shaft
A11
properly slides into the centre part of the fan
blades
A14
. Push the fan blades
A14
towards the motor unit
A2
all the way. Now, check that the fan blades
A14
turn freely, and
secure them in place by screwing nut
A15
anticlockwise on to the
shaft
A11
.
■
Release the clamps along the perimeter of the rear protective
grill
A12
. Place the front protective grill
A16
against the rear
protective grill
A12
so that the front grill
A16
fits into the
alignment hook in the bottom part of the rear protective grill
A12
and so that the screw holes in the top part of the grills are aligned.
Fasten the released clamps along the perimeter of the grills. To
ensure a strong connection of the two grills, into the aligned holes
at the top of the grills it is necessary to screw in the supplied screw
and secure it with the nut.
■
Before putting the fan into operation, check that it is correctly
assembled and that the protective grills are firmly joined.
■
To disassemble, proceed in reverse sequence.
OPERATING THE APPLIANCE
Setting the speed and turning off the fan
■
Place the fan on an even, dry and smooth surface within reach of
a power socket. Connect the power cord to a power socket. To set
the air flow speed, use the buttons on the control panel
A3
. The
functions of the control buttons are described below:
0 – turn off the fan;
1 – set a low air flow speed;
2 – set a medium air flow speed;
3 – set a high air flow speed.
■
When you have finished using the fan, always turn it off and
disconnect it from the power socket.
Setting horizontal oscillation
■
The horizontal oscillation of the motor unit
A1
can be set using
the toggle switch
A2
. To start the horizontal oscillation, push the
toggle switch
A1
down. The motor unit
A2
will oscillate from side
to side at an angle of approximately 90°.
■
To turn off the oscillation, pull the toggle switch
A1
up. This will
turn off the oscillation.
Setting the vertical tilt angle of the motor unit
■
Before setting the vertical tilt angle of the motor unit
A2
, first turn
off the fan. Set the desired angle of the motor unit
A2
and then
you may start the fan again.
Note:
The motor unit
A2
may only be tilted up and down in
a limited range. Do not set the tilt angle of the motor unit
A2
by force.
Setting the height of the fan
■
The height of the fan may be set in the range from 102 to 120 cm.
■
Turn off the fan before setting its height. Use one hand to firmly
hold the outer pole
A7
and the other hand to release the inner
extension lock
A6
by turning the locking screw anticlockwise.
Slide the inner extensible pole
A5
in or out to set the desired fan
height. To lock the set height in place, tighten the locking screw
clockwise.
