- 7 -
Copyright © 2019, Fast ČR, a.s.
09/2019
process starts, the display
B3
will show the symbol
. The brewed
coffee will flow into the kettle
A6
.
Note:
If you need to interrupt the coffee brewing process, press
the button
ON / OFF
B8
. Press the
ON / OFF B8
button
again to resume the brewing process. The glass kettle
A6
can be taken out of the kettle and coffee can be served.
The brewing process will automatically be interrupted,
however, the duration of the interruption must, in this
case, not exceed 30 seconds. There is a risk the coffee in
the permanent filter
A2
overflowing and damaging the
appliance.
12. As soon as the coffee brewing process is finished, the symbol
will disappear from the display
B3
and the appliance will beep. The
coffeemaker will automatically switch to the coffee heating mode, in
which the hotplate
A14
will heat the coffee for 35 minutes. To keep
the coffee warm, always place the glass kettle
A6
on the hotplate
A14
. If the glass kettle
A6
is empty, do not place it on the hotplate
A14
. This could damage it.
Note:
Allow the coffeemaker to cool down for approx. 10 minutes
before using it again. Otherwise, there is a risk of it
overheating and subsequent damage.
13. When not using the coffeemaker, disconnect the power plug from
the power socket. Allow the coffeemaker to sufficiently cool down
and then clean it according to the instructions in chapter "Cleaning
and maintenance".
Attention:
Be very careful, when pouring coffee from the kettle
A6
. The coffee is very hot. Carefully pour out the coffee
at an angle no greater than 45°. If you were to pour
the coffee out too fast at too steep an angle, the lid
could come loose and scalding from very hot coffee
could result.
Attention:
Do not touch the hotplate
A14
while the coffeemaker
is in operation. The hotplate
A14
is very hot and
presents a risk of burns.
Brewing coffee from ground coffee
1. Open the lid
A10
and pour clean cold water into the water tank
A12
up to the maximum level mark. Never fill the water past the
maximum mark.
2. Press button
A11
and open the steam chamber
A5
.
3. Pour a sufficient amount of ground coffee into the permanent filter
A2
. Use ground coffee specifically intended for this type of appliance
exclusively. As a rule, you will need a full tablespoon of ground coffee
for a single cup of coffee. Nevertheless, the amount of ground coffee
can be modified to suit one's preferences.
4. Insert the filter holder
A3
, the permanent filter
A2
and the filter lid
A1
into the steam chamber
A5
. Check that all the components are
properly inserted.
5. Close the steam chamber
A5
. Correct closure is indicated by a click.
6. Place the glass kettle
A6
on to the hotplate
A14
.
7. Insert the power plug into a power socket and the time will start
flashing on the display
B3
if it was set previously, otherwise "12:00"
will start flashing.
8. Use the
2 - 12 CUPS B4
button to set the number of coffee cups to
be brewed in the range from 2 to 12. The set number is shown on
the display
B3
. The default number is 12 cups.
Note:
If the number of cups to be brewed is not set using the
2 -
12 CUPS B4
button, the coffeemaker will brew the default
number – 12 cups.
9. Always check that the amount of water in the water tank corresponds
to the number of cups of coffee set using the
2 - 12 CUPS B4
button.
The coffeemaker will always consume all the water in the water
tank
A12
.
10. Press the
GRIND OFF
B11
button to skip the coffee grinding phase.
Indicator light
B10
will turn on.
11. Press the
ON / OFF
B8
button. Indicator light
B7
will be lit and after
a short moment the coffee brewing process will start automatically.
When the coffee brewing process starts, the display
B3
will show
the symbol
. The brewed coffee will flow into the kettle
A6
.
Note:
If you need to interrupt the coffee brewing process, press
the button
ON / OFF
B8
. Press the
ON / OFF B8
button
again to resume the brewing process. The glass kettle
A6
can be taken out of the kettle and coffee can be served.
The brewing process will automatically be interrupted,
however, the duration of the interruption must, in this
case, not exceed 30 seconds. There is a risk the coffee in
the permanent filter
A2
overflowing and damaging the
appliance.
12. As soon as the coffee brewing process is finished, the symbol
will disappear from the display
B3
and the appliance will beep. The
coffeemaker will automatically switch to the coffee heating mode, in
which the hotplate
A14
will heat the coffee for 35 minutes. To keep
the coffee warm, always place the glass kettle
A6
on the hotplate
A14
. If the glass kettle
A6
is empty, do not place it on the hotplate
A14
. This could damage it.
Note:
Allow the coffeemaker to cool down for approx. 10 minutes
before using it again. Otherwise, there is a risk of it
overheating and subsequent damage.
13. When not using the coffeemaker, disconnect the power plug from
the power socket. Allow the coffeemaker to sufficiently cool down
and then clean it according to the instructions in chapter "Cleaning
and maintenance".
Automatic start
The coffeemaker is equipped with an automatic start function. Thanks to
this function, you will be able to start the coffeemaker at a time of your
choosing. Before setting this function, check that you have properly set
the time – see chapter "
Setting the time
".
1. Perform steps 1 – 10 from chapter "
Brewing coffee from coffee
beans
" or from chapter "
Brewing coffee from ground coffee
".
2. Hold down the
PROGRAM
B1
button. The hours will start flashing
on display
B3
.
3. While the hours on the display
B3
are flashing, use buttons
HOUR
B5
and
MIN B6
to set the time when the coffeemaker should turn
on automatically.
4. To confirm the setting, press button
PROGRAM B1
. Symbol
will
appear and indicator light
B2
will be lit on the display
B3
.
Note:
If you do not confirm the automatic start time by pressing
button
PROGRAM B1
, the time will not be saved and the
coffeemaker will not start automatically. The automatic
start setting is correctly set when symbol
is shown
and indicator light
B2
is lit on the display
B3
.
5. When the time arrives for the coffeemaker to start, the indicator
light
B7
will be lit and after a short moment the coffee brewing
process will start.
Note:
If you need to cancel the automatic start function, press
button
PROGRAM B1
and the coffee brewing process will
start automatically within a few moments.
If you wish to change the automatic start time, again
perform the steps 2 – 4 above.
Coffee brewing tips
Keep the coffeemaker in a clean condition. Regularly remove limescale
deposits that may negatively affect the flavour of the brewed coffee.
