- 7 -
05/2021
Copyright © 2021, Fast ČR, a.s.
PRESET BLENDING MODES
■
This blender has two blending modes. Both modes have their preset speed and
blending duration and their settings cannot be changed. The use of modes is
described in the following table.
Mode
Ingredients
Preset blending time
SOFT
Fruit and vegetables of soft consistency
(strawberries, tomatoes, bananas, etc.)
40 seconds
Salsa
Sauces
HARD
Fruit and vegetables of firm consistency
(carrots, apples, pears, pineapple, etc.)
60 seconds
Smoothie beverages and cocktails
Frozen food
Baby food, side dishes
BLENDING
■
Insert the the power plug to a power socket.
Note:
The motor unit base is equipped with a safety mechanism that will
prevent it from being turned on unless it is correctly assembled. In the
event that blending does not start, it is possible that the jar or bottle is
incorrectly mounted. Release the jar/bottle and mount it again according
to the procedure above.
■
Based on the type of ingredient, start blending by pressing button
SOFT
or
HARD
.
Blending runs automatically without the need to hold down the mode button, and
its progress is shown by the LED indicator
B1
. When the preset time has elapsed, the
blending will stop automatically.
■
Blending can be stopped at any time by again pressing the mode button in which
the blender is running. Blending can be restarted by pressing the same button.
■
If after completing the blending cycle you are not satisfied with the resulting
mixture, you may repeat the whole cycle again by pressing button
SOFT
or
HARD
.
Attention:
The maximum operating time is 2 minutes. Do not leave the
blender running non-stop for longer than the specified operating
time. Then, allow the appliance to cool down for 2 minutes. When
blending tougher ingredients or thicker liquids, do not leave the
blender running for longer than 1 minute.
■
When blending in the glass blending jar
A3
, you may also add solid and liquid
ingredients into the jar through the hole in the lid
A2
after removing the inner cap
A1
. However, never open the outer lid
A2
during operation. When processing hot
liquids, the inner cap
A1
must remain closed.
■
In the event that ingredients are getting stuck on the blade assembly or the walls
of the jar or bottle, turn off the blender by pressing the button of the mode that
is running and wait for the blade assembly to come to a complete stop. Then
disconnect the blender from the power socket. Then, proceed as follows:
- When blending in the glass blending jar, remove its outer lid and using a plastic
spatula, clean the blade assembly and the walls of the blending jar. Put the lid
back on.
- When blending in the sports bottle, rotate the bottle in the direction of the open
padlock and take it off the base unit by pulling it out upwards. Turn the bottle so
that the blade assembly is on top and screw off the blade assembly. Use a plastic
spatula to clean the blade assembly and the walls of the bottle. Then screw the
blade assembly back on and mount the bottle back on to the base unit.
■
Reconnect the blender to the power grid and continue blending by pressing the
button of the respective mode.
ENDING BLENDING
■
When you have finished blending, disconnect the power cable of the blender
from the power socket and remove the blending jar or bottle from the base unit
by turning it in the direction of the open padlock on the base unit and pulling it
upwards.
■
If you have been blending in the glass jar, remove its outer lid and pour its contents
into another suitable container or bottle or into the remaining sports bottles.
■
If you have been blending in the sports bottle, turn the bottle upside down and
screw off the blade assembly. You can leave the contents in the bottle and simply
close it with the lid
A11
or
A12
.
■
Clean the blender and the used accessories according to the instructions in chapter
CLEANING AND MAINTENANCE.
CLEANING AND MAINTENANCE
Attention:
Prior to any cleaning or maintenance, always disconnect the
blender from the power grid.
The motor base unit and its power cord are not intended for
washing in a dishwasher. Do not spray these parts with water or
any other liquid or submerge them in water or any another liquid.
Never use chemicals, dishwashing wool, steel wool or cleaning
agents with an abrasive component since these may seriously
damage the surface of the base unit.
■
We recommend cleaning the emptied blending jar or bottle as soon as possible
after use so that the blended ingredients do not stick to the walls. Ingredients that
have dried on, are very difficult to remove.
■
To quickly clean the jar or the bottle, pour in some clean water up to the maximum
mark, and add a small amount of neutral dishwashing detergent. Then mount the
assembled jar or bottle on to the base unit and start the
SOFT
mode. When you
have finished the mode, disconnect the blender, remove the jar/bottle and empty
its contents out into a sink.
■
Disassemble the jar or bottle into its individual parts and then wash them all in hot
water with a small amount of kitchen detergent, rinse out with clean water and wipe
dry. Parts
A3
,
A8
and
A10
may be washed in a dishwasher.
Warning:
When cleaning and handling the blade assembly
A4
or
A9
, be
very careful not to injure yourself. The blades are sharp.
Certain foods may cause discolouration of the jar or bottles. This,
however, has no effect on the operation of the blender.
■
Wipe the outer parts of the motor base unit using a lightly dampened wiping cloth
or sponge, and then wipe dry.
STORAGE
■
Before storing it, the blender and its accessories must be disconnected from the
power supply, clean and dry.
■
Store the blender and its accessories in a clean, dry place out of children's reach.
Attention:
Keep the stored blender away from extreme temperatures, direct
sunlight and excessive humidity and do not store it in an overly
dusty environment.
TECHNICAL SPECIFICATIONS
Rated voltage range .................................................................................................... 220−240 V AC
Rated frequency........................................................................................................................50/60 Hz
Power output ..................................................................................................................................800 W
Volume of the glass jar .................................................................................................................... 0.9 l
Volume of the sports bottle ........................................................................................................... 0.6 l
Electrical shock protection class ........................................................................................................II
Noise level ...................................................................................................................................85 dB(A)
The declared noise emission level of the appliance is 85 dB(A), which represents a level
A of acoustic power with respect to a reference acoustic power of 1 pW.
Explanation of technical terminology
Safety class for electrical shock protection:
Class II – Electrical shock protection is provided by double or heavy-duty insulation.
Changes to text and technical parameters are reserved.
INSTRUCTIONS AND INFORMATION REGARDING THE
DISPOSAL OF USED PACKAGING MATERIALS
Dispose of used packaging material at a site designated for waste in your municipality.
DISPOSAL OF USED ELECTRICAL AND ELECTRONIC
EQUIPMENT
This symbol on products or original documents means that used
electric or electronic products must not be added to ordinary
municipal waste. For proper disposal, renewal and recycling, hand
over these appliances to determined collection points. Alternatively,
in some European Union states or other European countries you may
return your appliances to the local retailer when buying an equivalent
new appliance.
Correct disposal of this product helps save valuable natural resources
and prevents potential negative effects on the environment and human health, which
could result from improper waste disposal. Ask your local authorities or collection
facility for more details.
In accordance with national regulations penalties may be imposed for the incorrect
disposal of this type of waste.
For business entities in European Union states
If you want to dispose of electric or electronic equipment, ask your retailer or supplier
for the necessary information.
Disposal in other countries outside the European Union.
This symbol is valid in the European Union. If you wish to dispose of this product,
request the necessary information about the correct disposal method from the local
council or from your retailer.
This product meets all the basic requirements of EU directives related to
it.
