Sencon SI9550 Instructions Manual Download Page 2

Page: 2 / 17

Hoverprobe Refurbishment

RECOGNIZING THE TWO MODELS ........................................................................... 3

PACKING LIST .......................................................................................................... 4

HOVERPROBE REFURBISHMENT INSTRUCTIONS ..................................................... 5

3.1

WITCH ASSEMBLY

.................................................................................................... 9

3.1.1

SI9650 ........................................................................................................... 9

3.1.2

SI9550 ......................................................................................................... 10

3.2

INAL ASSEMBLY

..................................................................................................... 12

HOVERPROBE TEST ............................................................................................... 14

REVISION LIST ....................................................................................................... 15

FAX BACK SUGGESTION PAGE ............................................................................... 16

CONTACTS DETAILS FOR SENCON ......................................................................... 17

It is strongly advised that you

watch the enclosed video CD prior

to carrying out this refurbishment.

Summary of Contents for SI9550

















