selftrack NITRO User & Installation Manual Download Page 3

Selftrack Nitro Vehicle Tracker 

User & Installation Manual 
 

Page 3 

 

REGULATORY COMPLIANCE 

FCC 

The  modem  was  tested  and  certified  to  meet  FCC  Parts  15  in  a  stand-alone  configuration,  which  demonstrated  that  the 
GSM2338 Nitro complies with Part 15 emission limits. FCC Part 22 & Part 24 is covered by the Enfora Enabler IIIG  “modular 
approval” process for a transmitter. This approach, described by FCC Public Notice DA 00-131407 released June 26, 2000, is 
intended to afford relief to equipment manufactures by eliminating the requirement for obtaining a new equipment authorization 
for the same transmitter when installed in a new device. 

In  order  to  use  the  GSM2338  Nitro  without  additional  FCC  certification  approvals,  the  installation  must  meet  the  following 
conditions: 

For  the  transmitter  to  meet  the  MPE  categorical  exclusion  requirements  of  2.1091,  the  ERP  must  be  less  than  1.5  watts  for 
personnel separation distance of at least 20 cm (7.9in). Therefore the maximum antenna gain cannot 3.3dBi. If greater 
than 1.5 watts exists, then additional testing and FCC approval is required. 

R&TTE - 

 

The GSM2338 Nitro modem has been fully tested and complies with all the requirements of EN301 489-1, EN301 489-7 and 
EN60950-1:2002.  Compliance  to  EN301  511  has  been  demonstrated  by  testing  on  both  the  GSM2338  and  the  integrated 
GSM0308 module. 

DISCLAIMER 

The  information  and  instructions  contained  within  this  publication  comply  with  all  FCC,  GCF,  PTCRB,  R&TT,  IMEI  and  other 
applicable codes that are in effect at the tome of publication. Enfora disclaims all responsibility for any act or omissions, or for 
breach of law, code or regulation, including local or state codes, performed by a third party. 

Enfora strongly recommends that all installations, hookups, transmissions ect., be preformed by persons who are experienced in 
the fields of radio frequency technologies. Enfora acknowledges that the installation, setup and transmission guidelines contained 
within this publication are guidelines, and that each installation may have variables outside of the guidelines contained herein. 
Said  variables  must  be  taken  into  consideration  when  installing  or  using  the  product,  and  Enfora  shall  not  be  responsible  for 
installations or transmissions that fall outside of the parameters set forth in this publication. 

Enfora shall not be liable for consequential or incidental damages, injury to any person or property, anticipated or lost profits, loss 
of time, or other losses incurred by Customer or any third party in connection with the installation of the Products or Customer’s 
failure to comply with the information and instructions contained herein. 

WARRANTY INFORMATION 

LIMITED WARRANTY 

Enfora warrants to the original purchaser of the product that, for a period of one (1) year from the date of product purchase, the 
product hardware, when used in conjunction with any associated software (including any firmware and applications such as the 
modem manager) supplied by Enfora, will be free from defects in material or workmanship under normal operation. Enfora further 
warrants  to  such  original  purchaser  that,  for  a  period  of  ninety  (90)  days  from  the  date  of  product  purchase,  any  software 
associated with the product will perform substantially in accordance with the user documentation provided by Enfora, and any 
software media provided with the product will be free from defects in material or workmanship under normal operation. Enfora 
does  not  warrant  that  the  product  hardware  or  any  associated  software  will  meet  the  purchaser’s  requirements  or  that  the 
operation of the product hardware or software will be uninterrupted or error-free. This limited warranty is only for the benefit of the 
original purchaser and is not transferable. 

During the warranty period applicable  to the product hardware, Enfora, at its expense and in  its sole  discretion, will repair or 
replace the product if it is determined to have a covered hardware defect, provided that the purchaser first notifies Enfora of any 
such defects, furnishes Enfora with a proof of purchase, requests and obtains a return merchandize authorization (RMA) number 
from Enfora, and returns the product, shipping charges prepaid, to Enfora under that RMA. If, upon reasonable examination of 

Summary of Contents for NITRO















Reviews: