Sejin Electron SPR-8695TU User Manual Download Page 2

FCC NOTICE 

 

 

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC FULES. 

OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITION: 

(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND 

(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,   

INCLUDING INTERFERENCE THAT MAY CAUSE UNDERSIRED   

OPERATION.  

 

 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to 

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 

interference in a residential installation. This equipment generates, uses and can radiate radio frequency 

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to 

radio communication. However, there is no guarantee that interference will not occur in a particular 

installation.  

If this equipment does cause harmful interference to radio or television reception, which can be determined 

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more 

of the following measures :   
 
- Reorient or relocate the receiving antenna.   
 
- Increase the separation between the equipment and receiver.   
 
- Connect the equipment into an outlet on a circuit difference from that to which   
    the receiver is connected.   
 
- Consult the dealer of an experienced radio/TV technician for help.   
 
 
NOTE : The manufacturer is not responsible for any radio or TV interference caused by   
unauthorized modifications to this equipment. Such modifications could void the user’s   
authority to operate the equipment.   
 
 

Summary of Contents for SPR-8695TU









Reviews: