background image

2. Foreword 

Thank you for choosing the MDS-12 marine radar antenna. The radar antenna is designed and 

constructed to meet the rigorous demands of the marine environment. However,  no  machine  can 

perform its intended function unless properly installed and maintained. Please carefully read and 

follow the recommended procedures for installation, operation and maintenance. While this unit can 

be installed by the purchaser, any purchaser who has doubts about his or her technical abilities may 

wish to have the unit installed by an authorized Dealer or other qualified technician.

We want to Hear from you!

Your  suggestions  and  comments  are  highly  important  to  us.  Please  send  us  your  feedback  at 

[email protected].

AvMap Srl

Viale Zaccagna 6, 54033 Carrara (MS), Italy

Customer support: +39-0585-784044

[email protected]

2.1 Features

The main features of the MDS-12 marine radar antenna:

 

Built-in ethernet RJ45 connection cable to connect via a WiFi router to Seiwa Explorer 23 WiFi, 
and to SWx charplotter series. (WiFi Router not included in the box). 

 

4kW  high power all weather radar

 

36NM range  

 

Traditional SEIWA quality and reliability in a compact, lightweight and low-cost radar antenna.

 

Digital radar target technology.

 

Built-in excellent sea and rain clutter algorithm.

 

Fully digital signal processing.

 

High performance microwave front end.

2.2 Technical Specifications

ANTENNA UNIT

 

Radiator: Slotted waveguide array

 

Radiator length: 55 cm

 

Horizontal beamwidth: 4°

 

Vertical beamwidth: 25°

 

Sidelobe:

 

20° off mainlobe; less than -18 dB 

 

O 20° off mainlobe; less than -23 dB

 

●Polarization: Horizontal

 

Antenna rotation speed: 24 rpm (+ 2)

 

Wind resistance: Relative wind speed 100 knots (51.5 m/s)

TRANSCEIVER MODULE (contained in radome)

 

Transmitting tube: MSF1421B or MAF1421B

 

Frequency: 9410 MHz + 30MHz

 

●Peak output power: 4kW nominal

 

●Pulselength & pulse repetition rate:

Summary of Contents for SI-TEX MDS-12









Reviews: